REAR DIFFERENTIAL CARRIER ASSEMBLY > REASSEMBLY > Preparation
 | 09308-00010 | Oil Seal Puller |
 | 09316-60011 | Transmission & Transfer Bearing Replacer |
 | (09316-00011) | Replacer Pipe |
 | (09316-00021) | Replacer A |
 | (09316-00041) | Replacer C |
 | 09330-00021 | Companion Flange Holding Tool |
 | (09330-00030) | Pin |
 | 09504-00011 | Differential Side Bearing Adjusting Nut Wrench |
 | 09506-30012 | Differential Drive Pinion Rear Bearing Cone Replacer |
 | 09554-30011 | Differential Oil Seal Replacer |
 | 09636-20010 | Upper Ball Joint Dust Cover Replacer |
 | 09930-00010 | Drive Shaft Nut Chisel |
 | (09931-00010) | Handle |
 | (09931-00020) | Nut Chisel |
 | 09950-30012 | Puller A Set |
 | (09951-03010) | Upper Plate |
 | (09953-03010) | Center Bolt |
 | (09954-03010) | Arm |
 | (09955-03030) | Lower Plate 130 |
 | (09956-03030) | Adaptor 20 |
 | 09950-60010 | Replacer Set |
 | (09951-00430) | Replacer 43 |
 | (09951-00470) | Replacer 47 |
 | (09951-00480) | Replacer 48 |
 | (09951-00550) | Replacer 55 |
 | 09950-70010 | Handle Set |
 | (09951-00560) | Replacer 56 |
 | (09951-00570) | Replacer 57 |
 | (09951-07150) | Handle 150 |
 | 09960-10010 | Variable Pin Wrench Set |
 | (09962-01000) | Variable Pin Wrench Arm Assy |
 | (09963-00700) | Pin 7 |
| Brass bar | - |
| Chisel | - |
| Dial indicator | - |
| Feeler gauge | - |
| Hammer | - |
| Micrometer | - |
| Needle nose pliers | - |
| Plastic hammer | - |
| Press | - |
| Red lead | - |
| Screwdriver | - |
| Tape | - |
| Torque wrench | - |
| Vernier calipers | - |
| Item | Capacity | Classification | |
| Front differential | w/ A.D.D. | 1.60 to 1.70 liters (1.69 to 1.80 US qts, 1.40 to 1.50 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 |
| w/o A.D.D. | 1.40 to 1.50 liters (1.48 to 1.59 US qts, 1.23 to 1.31 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 | |
| Rear differential | 2WD | 3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 |
| 4WD | 3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 | |
 | 09011-12301 | Socket Wrench 30 mm | - |
 | 09031-00030 | Pin Punch | - |
 | 09044-00010 | Torx Socket E14 | - |
 | 09905-00012 | Snap Ring No.1 Expander | - |
 | 09905-00013 | Snap Ring Pliers | - |
 | 08833-00090 | Adhesive 1131, THREE BOND 1131, LOCTITE 518 or equivalent | - |
 | 08833-00100 | THREE BOND 1360K or equivalent | - |