REAR DIFFERENTIAL CARRIER ASSEMBLY > DISASSEMBLY > Preparation
 | 09308-00010 | Oil Seal Puller |
 | 09308-10010 | Oil Seal Puller |
 | 09330-00021 | Companion Flange Holding Tool |
 | (09330-00030) | Pin |
 | 09556-22010 | Drive Pinion Front Bearing Remover |
 | 09930-00010 | Drive Shaft Nut Chisel |
 | (09931-00010) | Handle |
 | (09931-00020) | Nut Chisel |
 | 09950-00020 | Bearing Remover |
 | 09950-30012 | Puller A Set |
 | (09951-03010) | Upper Plate |
 | (09953-03010) | Center Bolt |
 | (09954-03010) | Arm |
 | (09955-03030) | Lower Plate 130 |
 | (09956-03030) | Adaptor 20 |
 | 09950-40011 | Puller B Set |
 | (09951-04020) | Hanger 200 |
 | (09952-04010) | Slide Arm |
 | (09953-04030) | Center Bolt 200 |
 | (09954-04010) | Arm 25 |
 | (09955-04061) | Claw No.6 |
 | (09957-04010) | Attachment |
 | (09958-04011) | Holder |
 | 09950-60010 | Replacer Set |
 | (09951-00360) | Replacer 36 |
 | (09951-00380) | Replacer 38 |
 | 09950-70010 | Handle Set |
 | (09951-07150) | Handle 150 |
| Brass bar | - |
| Chisel | - |
| Dial indicator | - |
| Feeler gauge | - |
| Hammer | - |
| Micrometer | - |
| Needle nose pliers | - |
| Plastic hammer | - |
| Press | - |
| Red lead | - |
| Screwdriver | - |
| Tape | - |
| Torque wrench | - |
| Vernier calipers | - |
| Item | Capacity | Classification | |
| Front differential | w/ A.D.D. | 1.60 to 1.70 liters (1.69 to 1.80 US qts, 1.40 to 1.50 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 |
| w/o A.D.D. | 1.40 to 1.50 liters (1.48 to 1.59 US qts, 1.23 to 1.31 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 | |
| Rear differential | 2WD | 3.15 to 3.25 liters (3.30 to 3.43 US qts, 2.77 to 2.86 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 |
| 4WD | 3.30 to 3.40 liters (3.49 to 3.59 US qts, 2.90 to 2.99 lmp. qts.) | Hypoid gear oil APL GL-5 Above-18°C (0°F): SAE 90) Below-18°C (0°F): SAE 80W or 80W-90 | |
 | 09011-12301 | Socket Wrench 30 mm | - |
 | 09031-00030 | Pin Punch | - |
 | 09044-00010 | Torx Socket E14 | - |
 | 09905-00012 | Snap Ring No.1 Expander | - |
 | 09905-00013 | Snap Ring Pliers | - |
 | 08833-00090 | Adhesive 1131, THREE BOND 1131, LOCTITE 518 or equivalent | - |
 | 08833-00100 | THREE BOND 1360K or equivalent | - |