MANUAL TRANSMISSION UNIT
Counter 5th gear thrust clearance
| Standard
| 0.10 to 0.35 mm (0.0039 to 0.0138 in.)
|
Counter 5th gear radial clearance
| Standard
| 0.015 to 0.068 mm (0.0059 to 0.0027 in.)
|
Counter 5th gear inner diameter
| Standard
| 38.015 to 38.040 mm (1.4967 to 1.4976 in.)
|
Maximum
| 38.040 mm (1.4976 in.)
|
Counter gear rear shaft snap ring
| 0.1 mm (0.0039 in.) or less
|
Counter gear rear shaft snap ring thickness
| A
| 2.80 to 2.85 mm (0.1102 to 0.1122 in.)
|
B
| 2.85 to 2.90 mm (0.1122 to 0.1141 in.)
|
C
| 2.90 to 2.95 mm (0.1141 to 0.1160 in.)
|
D
| 2.95 to 3.00 mm (0.1160 to 0.1181 in.)
|
E
| 3.00 to 3.05 mm (0.1181 to 0.1200 in.)
|
F
| 3.05 to 3.10 mm (0.1200 to 0.1220 in.)
|
G
| 3.10 to 3.15 mm (0.1220 to 0.1240 in.)
|
Reverse idler gear radial clearance
| Standard
| 0.040 to 0.082 mm (0.0016 to 0.0032 in.)
|
Reverse idler gear clearance
| Standard
| 0.05 to 0.35 mm (0.0020 to 0.0138 in.)
|
Reverse idler gear diameter
| Standard
| 24.040 to 24.061 mm (0.9465 to 0.9473 in.)
|
Maximum
| 24.061 mm (0.9473 in.)
|
Reverse idler gear shaft outer diameter
| Standard
| 23.979 to 24.000 mm (0.9441 to 0.9449 in.)
|
Maximum
| 23.979 mm (0.9441 in.)
|
Synchronizer ring No. 3 clearance
| 0.68 to 1.32 mm (0.0268 to 0.0520 in.)
|
Transmission hub sleeve No. 3 clearance
| 0.26 to 0.84 mm (0.0102 to 0.0331 in.)
|
Output shaft bearing shaft snap ring thickness
| A
| 2.65 to 2.70 mm (0.1043 to 0.1063 in.)
|
B
| 2.70 to 2.75 mm (0.1063 to 0.1083 in.)
|
C
| 2.75 to 2.80 mm (0.1083 to 0.1102 in.)
|
D
| 2.80 to 2.85 mm (0.1102 to 0.1122 in.)
|
E
| 2.85 to 2.90 mm (0.1122 to 0.1141 in.)
|
F
| 2.90 to 2.95 mm (0.1141 to 0.1160 in.)
|
G
| 2.95 to 3.00 mm (0.1160 to 0.1181 in.)
|
H
| 3.00 to 3.05 mm (0.1181 to 0.1200 in.)
|
J
| 3.05 to 3.10 mm (0.1200 to 0.1220 in.)
|
K
| 3.10 to 3.15 mm (0.1220 to 0.1240 in.)
|
L
| 3.15 to 3.20 mm (0.1240 to 0.1260 in.)
|
M
| 3.20 to 3.25 mm (0.1260 to 0.1280 in.)
|
N
| 3.25 to 3.30 mm (0.1280 to 0.1299 in.)
|
P
| 3.30 to 3.35 mm (0.1299 to 0.1319 in.)
|
Q
| 3.35 to 3.40 mm (0.1319 to 0.1339 in.)
|
R
| 3.40 to 3.45 mm (0.1339 to 0.1358 in.)
|
S
| 3.45 to 3.50 mm (0.1358 to 0.1378 in.)
|
Transmission front bearing retainer oil seal depth
| 11.2 to 12.2 mm (0.4409 to 0.4803 in.)
|
Transfer adapter oil seal depth (R151F)
| 45.4 to 46.4 mm (1.787 to 1.827 in.)
|
Extension housing oil seal depth (R151)
| 0+-0.5 mm (0+-0.020 in.)
|
INPUT SHAFT
Synchronizer ring No. 2 clearance
| 0.70 to 1.70 mm (0.0276 to 0.0669 in.)
|
Input shaft shim clearance
| 0.1 mm (0.0039 in.) or less
|
Front bearing shaft snap ring thickness
| A
| 2.10 to 2.15 mm (0.0827 to 0.0846 in.)
|
B
| 2.15 to 2.20 mm (0.0847 to 0.0866 in.)
|
C
| 2.20 to 2.25 mm (0.0866 to 0.0886 in.)
|
D
| 2.25 to 2.30 mm (0.0886 to 0.0906 in.)
|
E
| 2.30 to 2.35 mm (0.0906 to 0.0925 in.)
|
F
| 2.35 to 2.40 mm (0.0925 to 0.0945 in.)
|
G
| 2.40 to 2.45 mm (0.0945 to 0.0965 in.)
|
OUTPUT SHAFT
1st gear thrust clearance
| 0.20 to 0.45 mm (0.0079 to 0.0177 in.)
|
2nd gear thrust clearance
| 010 to 0.25 mm (0.0039 to 0.0098 in.)
|
3rd gear thrust clearance
| 010 to 0.25 mm (0.0039 to 0.0098 in.)
|
1st gear radial clearance
| 0.020 to 0.073 mm (0.0008 to 0.0029 in.)
|
2nd gear radial clearance
| 0.015 to 0.068 mm (0.0006 to 0.0027 in.)
|
3rd gear radial clearance
| 0.015 to 0.068 mm (0.0006 to 0.0027 in.)
|
Output shaft outer diameter
| Standard: Part A
| 38.979 to 38.995 mm (1.5334 to 1.5352 in.)
|
Standard: Part B
| 46.984 to 47.000 mm (1.8498 to 1.8504 in.)
|
Standard: Part C
| 37.984 to 38.000 mm (1.4954 to 1.4961 in.)
|
Minimum: Part A
| 38.979 mm (1.5334 in.)
|
Minimum: Part B
| 46.984 mm (1.8498 in.)
|
Minimum: Part C
| 37.984 mm (1.4954 in.)
|
Output shaft flange thickness
| Standard
| 4.80 to 5.20 mm (0.1890 to 0.2047 in.)
|
Output shaft runout
| Maximum
| 0.03 mm (0.0012 in.)
|
3rd gear inner diameter
| Standard
| 44.015 to 44.040 mm (1.7329 to 1.7339 in.)
|
Maximum
| 44.040 mm (1.7339 in.)
|
2nd gear inner diameter
| Standard
| 53.015 to 53.040 mm (2.0872 to 2.0881 in.)
|
Maximum
| 53.040 mm (2.0881 in.)
|
1st gear inner diameter
| Standard
| 46.015 to 46.040 mm (1.812 to 1.8126 in.)
|
Maximum
| 46.040 mm (1.8126 in.)
|
Synchronizer ring No. 1 (For 1st gear) clearance
| 0.65 to 1.75 mm (0.0256 to 0.0689 in.)
|
Synchronizer ring No. 1 (For 2nd gear) clearance
| 0.65 to 1.65 mm (0.0256 to 0.0689 in.)
|
Synchronizer ring No. 1 (For 3rd gear) clearance
| 0.75 to 1.75 mm (0.0295 to 0.0650 in.)
|
Synchronizer ring No. 1 clearance
| 0.65 to 1.75 mm (0.0256 to 0.0689 in.)
|
Reverse gear clearance
| Standard
| 0.15 to 1.41 mm (0.0059 to 0.0161 in.)
|
Transmission hub sleeve No. 2
| 0.15 to 0.35 mm (0.0059 to 0.0138 in.)
|
Clutch hub shaft snap ring thickness
| A
| 1.80 to 1.85 mm (0.0709 to 0.0728 in.)
|
B
| 1.85 to 1.90 mm (0.0728 to 0.0748 in.)
|
C
| 1.90 to 1.95 mm (0.0748 to 0.0768 in.)
|
D
| 1.95 to 2.00 mm (0.0768 to 0.0787 in.)
|
E
| 2.00 to 2.05 mm (0.0787 to 0.0807 in.)
|
F
| 2.05 to 2.10 mm (0.0807 to 0.0827 in.)
|
G
| 2.10 to 2.15 mm (0.0827 to 0.0846 in.)
|
Transmission clutch hub No. 1
| 0.1 mm (0.0039 in.) or less
|
Output shaft bearing shaft snap ring
| A
| 2.30 to 2.35 mm (0.0906 to 0.0925 in.)
|
B
| 2.35 to 2.40 mm (0.0925 to 0.0945 in.)
|
C
| 2.40 to 2.45 mm (0.0945 to 0.0965 in.)
|
D
| 2.45 to 2.50 mm (0.0965 to 0.0984 in.)
|
E
| 2.50 to 2.55 mm (0.0984 to 0.1004 in.)
|
F
| 2.55 to 2.60 mm (0.1004 to 0.1024 in.)
|
G
| 2.60 to 2.65 mm (0.1024 to 0.1043 in.)
|
Transmission clutch hub No. 2
| 0.1 mm (0.0039 in.) or less
|
COUNTER GEAR AND REVERSE IDLER GEAR
Counter gear journal outer diameter
| Standard
| 29.984 to 30.000 mm (1.1805 to 1.1811 in.)
|
Minimum
| 29.984 mm (1.1805 in.)
|
Counter gear front bearing snap ring No. 2
| 0.1 mm (0.0039 in.) or less
|
Counter gear front bearing snap ring No. 2 thickness
| A
| 2.05 to 2.10 mm (0.0807 to 0.0827 in.)
|
B
| 2.10 to 2.15 mm (0.0827 to 0.0846 in.)
|
C
| 2.15 to 2.20 mm (0.0846 to 0.0866 in.)
|
D
| 2.20 to 2.25 mm (0.0866 to 0.0886 in.)
|
E
| 2.25 to 2.30 mm (0.0886 to 0.0906 in.)
|
F
| 2.30 to 2.35 mm (0.0906 to 0.0925 in.)
|
