RADIO ANTENNA CORD > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



2. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


3. REMOVE STEERING PAD ASSEMBLY


B112129E01

  1. Straighten the front wheels.

  1. Using a T30 "torx" socket, loosen the 2 screws until the groove along each screw circumference catches on the screw case.



    B085362E03

  1. Pull out the steering pad from the steering wheel and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Using a screwdriver, disconnect the airbag connector.

    CAUTION:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Disconnect the horn connector and remove the steering pad.



4. REMOVE STEERING WHEEL ASSEMBLY


G039068E01

  1. Remove the steering wheel set nut.

  1. Place matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



5. REMOVE STEERING COLUMN COVER LOWER


G039357E01

  1. Remove the 3 screws and cover lower.



6. REMOVE STEERING COLUMN COVER UPPER


G039357E01

  1. Remove the 3 screws and cover lower.



7. REMOVE INSTRUMENT CLUSTER FINISH PANEL


B111106E01

  1. Remove the clip.

  1. Detach the 2 claws and remove the panel.



8. REMOVE COMBINATION METER ASSEMBLY


B087852E01

NOTICE:
There are 2 types of combination meters. One type has a 40 pin connector and 16 pin connector. The other type only has a 40 pin connector.

  1. Remove the 3 screws <B>.

  1. Disconnect all connectors and remove the combination meter.



9. REMOVE HEATER CONTROL KNOB


B088680E02

  1. Remove the 3 control knobs.



10. REMOVE FRE/REC CONTROL KNOB


B111103E01

  1. Remove the control knob.



11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER


B113048E01

HINT:
To prevent the clips from falling, horizontally pull out the panel. Hold both sides of the panel in the locations indicated by the arrows in the illustration.

  1. Remove the screw <C>.

  1. Detach the 6 claws and 4 clips.

  1. NOTICE:
    Make sure the center registers are not removed.

    Disconnect all connectors and remove the panel.



12. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    I043226E01

  1. Detach the 2 claws and disconnect the A/C control.



    E111651E01

  1. Detach the 2 claws and disconnect the air inlet damper control cable.

  1. Disconnect the connector.



    E111652E01

  1. Detach the 2 claws and disconnect the heater control cable.

  1. Detach the 2 claws and disconnect the air mix damper control cable.

  1. Remove the A/C control.



13. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET


    B112964

  1. Remove the 4 screws.

  1. Disconnect all connectors and remove the radio receiver.



    B085607

  1. w/o Stereo opening cover:
    Remove the No. 1 radio bracket.

    1. Remove the 4 screws and radio bracket from the radio receiver.



    B085608

  1. w/o Stereo opening cover:
    Remove the No. 2 radio bracket.

    1. Remove the 4 screws and radio bracket from the radio receiver.



    B112965

  1. w/ Stereo opening cover:
    Remove the No. 1 radio bracket.

    1. Remove the 4 screws and radio bracket from the radio receiver.



    B112966

  1. w/ Stereo opening cover:
    Remove the No. 2 radio bracket.

    1. Remove the 4 screws and radio bracket from the radio receiver.



14. REMOVE RADIO TUNER OPENING COVER WITH BRACKET


B089726E01

  1. Remove the 4 screws <F> and opening cover.



15. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B086888E01

  1. Push in the sides of the glove compartment door, as indicated by the arrows in the illustration. Then open the door to release it from the 2 stoppers. Open the door until it is horizontal.



    B086887E02

  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.



16. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY (w/ Airbag System)


B112127E01

  1. Disconnect the connector from the airbag.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.



    B112126

  1. Remove the 2 bolts.

  1. Detach the clamp from the bracket.



    B112264E01

  1. Detach the 12 claws and remove the airbag.



17. REMOVE INSTRUMENT PANEL DOOR (w/o Airbag System)


B086886E01

  1. Remove the 2 screws <D>.

  1. Detach the 8 claws and remove the instrument panel box door.



18. REMOVE FRONT PILLAR GARNISH LH

  1. Remove the front pillar garnish LH (Click here or Click here or Click here).



19. REMOVE FRONT PILLAR GARNISH RH

  1. Remove the front pillar garnish RH (Click here or Click here or Click here).>



20. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY UPPER



B086885E01

NOTICE:
Be careful not to damage the steering wheel.

  1. Remove the 2 bolts <A> and 2 screws <B>.

  1. Pull up the instrument panel to detach the 8 claws.

  1. Disconnect all connectors.

  1. Remove the instrument panel.



21. REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)



B115405E01

  1. Disconnect the connector.

  1. Detach the 5 clamps as shown in the illustration. Then remove the antenna cord.



22. REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)



B085617E01

  1. Disconnect the connector.

  1. Detach the 4 clamps as shown in the illustration. Then remove the antenna cord.