POWER WINDOW MASTER SWITCH > ON-VEHICLE INSPECTION

for Preparation Click here



1. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    B112007E04

  1. Measure the resistance of the door control switch.

    Standard resistance:
    LHD (Single cab, Extra cab):
    Tester Connection
    		Switch Condition
    		Specified Condition
    1 (E) - 2 (L)
    		Lock
    		Below 1 Ω
    1 (E) - 2 (L)
    1 (E) - 5 (UL)
    		OFF
    		10 kΩ or higher
    1 (E) - 5 (UL)
    		Unlock
    		Below 1 Ω
    RHD (Single cab, Extra cab):
    Tester Connection
    		Switch Condition
    		Specified Condition
    3 (L) - 10 (E)
    		Lock
    		Below 1 Ω
    3 (L) - 10 (E)
    4 (UL) - 10 (E)
    		OFF
    		10 kΩ or higher
    4 (UL) - 10 (E)
    		Unlock
    		Below 1 Ω
    Double cab:
    Tester Connection
    		Switch Condition
    		Specified Condition
    3 (E) - 5 (L)
    		Lock
    		Below 1 Ω
    3 (E) - 5 (L)
    3 (E) - 8 (UL)
    		OFF
    		10 kΩ or higher
    3 (E) - 8 (UL)
    		Unlock
    		Below 1 Ω

    If the result is not as specified, replace the switch assembly.



    B112772E03

  1. LHD (Single cab, extra cab):

    1. Measure the resistance of the power window switch.

    Standard resistance:
    Driver switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    Always
    (ON / OFF)
    		UP
    		1 (E) - 4 (DD)
    3 (DU) - 9 (B)
    		Below 1 Ω
    Always
    (ON / OFF)
    		OFF
    		1 (E) - 3 (DU)
    1 (E) - 4 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		DOWN
    		1 (E) - 3 (DU)
    9 (B) - 4 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		AUTO DOWN
    		1 (E) - 3 (DU)
    9 (B) - 4 (DD)
    		Below 1 Ω
    Passenger side switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		1 (E) - 10 (PD)
    9 (B) - 8 (PU)
    		Below 1 Ω
    OFF
    		OFF
    		1 (E) - 8 (PU)
    1 (E) - 10 (PD)
    		Below 1 Ω
    OFF
    		DOWN
    		1 (E) - 8 (PU)
    9 (B) - 10 (PD)
    		Below 1 Ω
    ON
    		UP
    		1 (E) - 10 (PD)
    		10 kΩ or higher
    9 (B) - 8 (PU)
    		Below 1 Ω
    ON
    		OFF
    		8 (PU) - 10 (PD)
    		Below 1 Ω
    ON
    		DOWN
    		1 (E) - 8 (PU)
    		10 kΩ or higher
    9 (B) - 10 (PD)
    		Below 1 Ω

    1. If the result is not as specified, replace the switch assembly.



    B085836E03

  1. RHD (Single cab, extra cab):

    1. Measure the resistance of the power window switch.

    Standard resistance:
    Driver switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    Always
    (ON / OFF)
    		UP
    		10 (E) - 5 (DD)
    2 (DU) - 9 (B)
    		Below 1 Ω
    Always
    (ON / OFF)
    		OFF
    		10 (E) - 2 (DU)
    10 (E) - 5 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		DOWN
    		10 (E) - 2 (DU)
    9 (B) - 5 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		AUTO DOWN
    		10 (E) - 2 (DU)
    9 (B) - 5 (DD)
    		Below 1 Ω
    Passenger side switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		10 (E) - 1 (PD)
    9 (B) - 8 (PU)
    		Below 1 Ω
    OFF
    		OFF
    		10 (E) - 8 (PU)
    10 (E) - 1 (PD)
    		Below 1 Ω
    OFF
    		DOWN
    		10 (E) - 8 (PU)
    9 (B) - 1 (PD)
    		Below 1 Ω
    ON
    		UP
    		10 (E) - 1 (PD)
    		10 kΩ or higher
    9 (B) - 8 (PU)
    		Below 1 Ω
    ON
    		OFF
    		8 (PU) - 1 (PD)
    		Below 1 Ω
    ON
    		DOWN
    		10 (E) - 8 (PU)
    		10 kΩ or higher
    9 (B) - 1 (PD)
    		Below 1 Ω

    1. If the result is not as specified, replace the switch assembly.



  1. LHD (Double cab):

    1. Measure the resistance of the power window switch.


    B112777E01


    Standard resistance:
    Driver switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    Always
    (ON / OFF)
    		UP
    		3 (E) - 9 (DD)
    4 (DU) - 6 (B)
    		Below 1 Ω
    Always
    (ON / OFF)
    		OFF
    		3 (E) - 4 (DU)
    3 (E) - 9 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		DOWN
    		3 (E) - 4 (DU)
    6 (B) - 9 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		AUTO DOWN
    		3 (E) - 4 (DU)
    6 (B) - 9 (DD)
    		Below 1 Ω
    Passenger side switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 15 (PD)
    6 (B) - 18 (PU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 18 (PU)
    3 (E) - 15 (PD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 18 (PU)
    6 (B) - 15 (PD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 15 (PD)
    		10 kΩ or higher
    6 (B) - 18 (PU)
    		Below 1 Ω
    ON
    		OFF
    		18 (PU) - 15 (PD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 18 (PU)
    		10 kΩ or higher
    6 (B) - 15 (PD)
    		Below 1 Ω
    Rear LH switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 13 (RLD)
    6 (B) - 12 (RLU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 12 (RLU)
    3 (E) - 13 (RLD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 12 (RLU)
    6 (B) - 13 (RLD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 13 (RLD)
    		10 kΩ or higher
    6 (B) - 12 (RLU)
    		Below 1 Ω
    ON
    		OFF
    		12 (RLU) - 13 (RLD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 12 (RLU)
    		10 kΩ or higher
    6 (B) - 13 (RLD)
    		Below 1 Ω
    Rear RH switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 16 (RRD)
    6 (B) - 10 (RRU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 10 (RRU)
    3 (E) - 16 (RRD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 10 (RRU)
    6 (B) - 16 (RRD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 16 (RRD)
    		10 kΩ or higher
    6 (B) - 10 (RRU)
    		Below 1 Ω
    ON
    		OFF
    		10 (RRU) - 16 (RRD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 10 (RRU)
    		10 kΩ or higher
    6 (B) - 16 (RRD)
    		Below 1 Ω

    1. If the result is not as specified, replace the switch assembly.



  1. RHD (Double cab):

    1. Measure the resistance of the power window switch.


    B112778E02


    Standard resistance:
    Driver switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    Always
    (ON / OFF)
    		UP
    		3 (E) - 9 (DD)
    4 (DU) - 6 (B)
    		Below 1 Ω
    Always
    (ON / OFF)
    		OFF
    		3 (E) - 4 (DU)
    3 (E) - 9 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		DOWN
    		3 (E) - 4 (DU)
    6 (B) - 9 (DD)
    		Below 1 Ω
    Always
    (ON / OFF)
    		AUTO DOWN
    		3 (E) - 4 (DU)
    6 (B) - 9 (DD)
    		Below 1 Ω
    Passenger side switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 13 (PD)
    6 (B) - 10 (PU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 10 (PU)
    3 (E) - 13 (PD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 10 (PU)
    6 (B) - 13 (PD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 13 (PD)
    		10 kΩ or higher
    6 (B) - 10 (PU)
    		Below 1 Ω
    ON
    		OFF
    		10 (PU) - 13 (PD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 10 (PU)
    		10 kΩ or higher
    6 (B) - 13 (PD)
    		Below 1 Ω
    Rear RH switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 15 (RRD)
    6 (B) - 16 (RRU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 16 (RRU)
    3 (E) - 15 (RRD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 16 (RRU)
    6 (B) - 15 (RRD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 15 (RRD)
    		10 kΩ or higher
    6 (B) - 16 (RRU)
    		Below 1 Ω
    ON
    		OFF
    		16 (RRU) - 15 (RRD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 16 (RRU)
    		10 kΩ or higher
    6 (B) - 15 (RRD)
    		Below 1 Ω
    Rear LH switch:

    Window Lock Switch Condition
    		Power Window Switch Condition
    		Tester Connection
    		Specified Condition
    OFF
    		UP
    		3 (E) - 12 (RLD)
    6 (B) - 18 (RLU)
    		Below 1 Ω
    OFF
    		OFF
    		3 (E) - 18 (RLU)
    3 (E) - 12 (RLD)
    		Below 1 Ω
    OFF
    		DOWN
    		3 (E) - 18 (RLU)
    6 (B) - 12 (RLD)
    		Below 1 Ω
    ON
    		UP
    		3 (E) - 12 (RLD)
    		10 kΩ or higher
    6 (B) - 18 (RLU)
    		Below 1 Ω
    ON
    		OFF
    		18 (RLU) - 12 (RLD)
    		Below 1 Ω
    ON
    		DOWN
    		3 (E) - 18 (RLU)
    		10 kΩ or higher
    6 (B) - 12 (RLD)
    		Below 1 Ω

    1. If the result is not as specified, replace the switch assembly.



    B112773E01

  1. LHD (Single cab, extra cab):
    Apply battery voltage to the master switch and check that the AUTO light illuminates.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 9 (B)
    Battery negative (-) → Terminal 1 (E)
    		AUTO light illuminates

    If the result is not as specified, replace the switch assembly.



    B085835E01

  1. RHD (Single cab, extra cab):
    Apply battery voltage to the master switch and check that the AUTO light illuminates.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 9 (B)
    Battery negative (-) → Terminal 10 (E)
    		AUTO light illuminates

    If the result is not as specified, replace the switch assembly.



    B079808E01

  1. LHD (Double cab):
    Apply battery voltage to the master switch and check that the AUTO light illuminates.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 6 (B)
    Battery negative (-) → Terminal 3 (E)
    		AUTO light illuminates

    If the result is not as specified, replace the switch assembly.



    B085830E01

  1. RHD (Double cab):
    Apply battery voltage to the master switch and check that the AUTO light illuminates.

    OK:
    Measurement Condition
    		Specified Condition
    Battery positive (+) → Terminal 6 (B)
    Battery negative (-) → Terminal 3 (E)
    		AUTO light illuminates

    If the result is not as specified, replace the switch assembly.