REAR SPEAKER (for Extra Cab) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.



1. INSTALL REAR NO. 1 SPEAKER ASSEMBLY


B085615

  1. Hold the speaker to the door.

  1. Install the speaker with the 3 screws.

  1. Connect the connector.



2. INSTALL QUARTER INSIDE TRIM BOARD

  1. Attach the claws and install the trim pocket to the trim board.



    B085707E01

  1. Attach the 7 clips and 6 claws to install the trim board.



3. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B113856E02

  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825

  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01

  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03

  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993

  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01

  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01

  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01

  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01

  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01

  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



5. INSTALL REAR SEATBACK ASSEMBLY


    B108088E01

  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the seatback's 2 hooks to the vehicle body.

  1. Install the seat with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 in.*lbf }



6. INSTALL BACK PANEL GARNISH LOWER


B085704E01

  1. Attach the 5 clips and 6 claws to install the garnish.



7. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    B115404E02

  1. Attach the seat cushion's 2 rear hooks to the vehicle body.



    B115402E01

  1. Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.

  1. Confirm that the seat cushion is firmly installed.



8. INSTALL REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



9. INSTALL BACK PANEL GARNISH UPPER


B086202E01

  1. Attach the 5 clips and 4 claws to install the garnish.



10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


11. PERFORM INITIALIZATION

  1. Perform initialization (Click here ).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.