ROOF HEADLINING (for Single Cab) > REMOVAL

for Preparation Click here

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

1. Using a screwdriver, detach the 8 claws.
   

   HINT:

   Tape the screwdriver tip before use.

2. Using a clip remover, detach the 4 clips and remove the scuff plate.
   

HINT:

Use the same procedures described for the LH side.

1. Remove the cap nut.
   

2. Using a clip remover, detach the 2 clips and remove the trim board.
   

HINT:

Use the same procedures described for the LH side.

1. w/ Assist grip:
   Using a screwdriver, detach the 4 claws and pry out the 2 assist grip plugs.
   

   HINT:

   Tape the screwdriver tip before use.

2. w/ Assist grip:
   Remove the 2 screws and the assist grip.
   

3. Using a clip remover, detach the 2 clips.
   

4. Pull the garnish in the direction indicated by the arrow in the illustration to detach the 2 claws. Then remove the garnish.
   

HINT:

Use the same procedures described for the LH side.

1. Using a screwdriver, detach the 4 claws.
   

   HINT:

   Tape the screwdriver tip before use.

2. Using a clip remover, detach the 5 clips and remove the garnish.
   

1. Single cab:
   Remove the outer belt shoulder anchor.
   
   

   1. Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.
      

      HINT:

      Tape the screwdriver tip before use.

   2. Remove the bolt and shoulder anchor.
      

2. Double cab:
   Remove the outer belt shoulder anchor.
   
   

   1. Using a screwdriver, disengage the 4 claws and remove the seat belt anchor cover cap.
      

      HINT:

      Tape the screwdriver tip before use.

   2. Remove the bolt and shoulder anchor.
      

3. w/o Pretensioner:
   Remove the bolt and seat belt.
   

4. w/ Pretensioner:
   
   

   1. Disconnect the pretensioner connector as shown in the illustration.
      

   
   
   

   2. Remove the bolt and seat belt.
      

1. Single cab:
   Remove the outer belt shoulder anchor.
   
   

   1. Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.
      

      HINT:

      Tape the screwdriver tip before use.

   2. Remove the bolt and shoulder anchor.
      

2. Double cab:
   Remove the outer belt shoulder anchor.
   
   

   1. Using a screwdriver, disengage the 4 claws and remove the seat belt anchor cover cap.
      

      HINT:

      Tape the screwdriver tip before use.

   2. Remove the bolt and shoulder anchor.
      

3. w/o Pretensioner:
   Remove the bolt and seat belt.
   

4. w/ Pretensioner:
   
   

   1. Disconnect the pretensioner connector as shown in the illustration.
      

   
   
   

   2. Remove the bolt and seat belt.
      

1. Using a screwdriver, detach the claw.
   

   HINT:

   Tape the screwdriver tip before use.

2. Using a clip remover, detach the 3 clips and remove the trim panel.
   

HINT:

Use the same procedures described for the LH side.

1. Using a clip remover, detach the 3 clips and remove the trim board.
   

HINT:

Use the same procedures described for the LH side.

1. Using a clip remover, remove the 3 clips and remove the back panel trim.
   

1. Remove the 2 screws and visor.
   

1. Remove the 2 screws and visor.
   

1. Remove the screw.
   

2. Using a screwdriver, detach the 2 claws and remove the holder.
   

   HINT:

   Tape the screwdriver tip before use.

HINT:

Use the same procedures described for the LH side.

1. Using a screwdriver, detach the 4 claws and open the 2 covers.
   

   HINT:

   Tape the screwdriver tip before use.

2. Remove the 2 screws and assist grip.
   

1. Using a clip remover, remove the 5 clips and headlining.
   

2. Remove the wire harness.