ROOF HEADLINING (for Double Cab) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH


2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH


3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH

  1. Install the 2 spacers.



4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH

  1. Install the 2 spacers.



5. INSTALL SIDE RAIL SPACER REAR LH

  1. LHD, w/o Rear roof assist grip:
    Install the 2 spacers.

  1. LHD, w/ Rear roof assist grip:
    Install the spacer.

  1. RHD, w/o Rear roof assist grip:
    Install the spacer.



6. INSTALL SIDE RAIL SPACER REAR RH

  1. LHD, w/o Rear roof assist grip:
    Install the spacer.

  1. RHD, w/o Rear roof assist grip:
    Install the 2 spacers.

  1. RHD, w/ Rear roof assist grip:
    Install the spacer.



7. INSTALL SIDE RAIL SPACER FRONT LH


8. INSTALL SIDE RAIL SPACER FRONT RH


9. INSTALL ROOF NO. 2 SILENCER PAD

  1. Install the 2 silencer pads.



10. INSTALL ROOF HEADLINING ASSEMBLY


B113446E01

  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. w/o Rear roof assist grip:
    Install the roof headlining with the 9 clips.

  1. w/ Rear roof assist grip:
    Install the roof headlining with the 5 clips.



11. INSTALL ASSIST GRIP


B111748E01

  1. w/o Rear roof assist grip:
    Install the assist grip with the 2 screws.

  1. w/o Rear roof assist grip:
    Close the 2 covers.

  1. w/ Rear roof assist grip:
    Install the 3 assist grip with the 6 screws.

  1. w/o Rear roof assist grip:
    Close the 6 covers.



12. INSTALL VISOR HOLDER LH


B111747

  1. Attach the 2 claws to install the holder.

  1. Install the screw.



13. INSTALL VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL VISOR ASSEMBLY LH

  1. Install the visor with the screw.



15. INSTALL VISOR ASSEMBLY RH

  1. Install the visor with the screw.



16. INSTALL ROOM LIGHT ASSEMBLY
Click here


17. INSTALL QUARTER INSIDE TRIM BOARD LH


B085560E01

  1. Attach the 4 clips to install the trim board.



18. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B113856E02

  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825

  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



20. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH


B113856E02

  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825

  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



21. INSTALL QUARTER TRIM PANEL LOWER LH


B085565E02

  1. Attach the 3 clips and claw to install the trim panel.



22. INSTALL QUARTER TRIM PANEL LOWER RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL BACK PANEL TRIM (w/ Back Panel Trim)

  1. Install the back panel trim with the 3 clips.



24. INSTALL BACK PANEL GARNISH UPPER


B086202E01

  1. Attach the 5 clips and 4 claws to install the garnish.



25. INSTALL FRONT PILLAR GARNISH LH


B111746E01

  1. Attach the 2 clips and 2 claws to install the garnish.

  1. w/ Assist grip:
    Install the assist grip with the 2 screws.

  1. w/ Assist grip:
    Attach the 4 claws to install the 2 assist plugs.



26. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



27. INSTALL CENTER PILLAR GARNISH LH


B085561E02

  1. Attach the clip and claw to install the garnish.



28. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



29. INSTALL CENTER PILLAR GARNISH LOWER LH


B085563E01

  1. Attach the 2 clips and 2 claws to install the garnish.



30. INSTALL CENTER PILLAR GARNISH LOWER RH

HINT:
Use the same procedures described for the LH side.



31. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01

  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03

  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993

  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01

  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01

  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01

  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01

  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01

  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



32. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01

  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03

  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993

  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01

  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01

  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01

  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01

  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01

  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


35. REMOVE REAR DOOR SCUFF PLATE LH


B085564E01

  1. Attach the 2 clips and 7 claws to install the scuff plate.



36. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



37. INSTALL COWL SIDE TRIM BOARD LH


B085566E01

  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



38. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



39. INSTALL FRONT DOOR OPENING TRIM LH


40. INSTALL FRONT DOOR OPENING TRIM RH


41. INSTALL FRONT DOOR SCUFF PLATE LH


B085562E01

  1. Attach the 3 clips and 7 claws to install the scuff plate.



42. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



43. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


44. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.