ROOF HEADLINING (for Extra Cab) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 3 SIDE RAIL SPACER REAR LH


2. INSTALL NO. 3 SIDE RAIL SPACER REAR RH


3. INSTALL NO. 2 SIDE RAIL SPACER REAR LH


4. INSTALL NO. 2 SIDE RAIL SPACER REAR RH


5. INSTALL SIDE RAIL SPACER REAR LH (for LHD)


6. INSTALL SIDE RAIL SPACER REAR RH (for RHD)


7. INSTALL SIDE RAIL SPACER FRONT LH


8. INSTALL SIDE RAIL SPACER FRONT RH


9. INSTALL NO. 2 ROOF SILENCER PAD


10. INSTALL ROOF HEADLINING ASSEMBLY


B113191E01

  1. Align the wire harness to the markings, and then install the wire harness with tape.

    NOTICE:
    Attach the roof wire harness securely.

  1. Install the roof headlining with the 5 clips.



11. INSTALL ASSIST GRIP

  1. Install the assist grip with the 2 screws.

  1. Close the 2 covers.



12. INSTALL VISOR HOLDER LH


B111747

  1. Attach the 2 claws to install the holder.

  1. Install the screw.



13. INSTALL VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.



14. INSTALL VISOR ASSEMBLY LH

  1. Install the visor with the screw.



15. INSTALL VISOR ASSEMBLY RH

  1. Install the visor with the screw.



16. INSTALL ROOM LIGHT ASSEMBLY
Click here


17. INSTALL ROOF SIDE GARNISH INNER UPPER LH


B085705E01

  1. Attach the 3 clips to install the garnish.



18. INSTALL ROOF SIDE GARNISH INNER UPPER RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL QUARTER PILLAR GARNISH LH


B085706E01

  1. Attach the 2 clips to install the garnish.



20. INSTALL QUARTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL QUARTER INSIDE TRIM BOARD LH

  1. Attach the claws and install the trim pocket to the trim board.



    B085707E01

  1. Attach the 7 clips and 6 claws to install the trim board.



22. INSTALL QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



23. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH


B113856E02

  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825

  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



24. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER RH


B113856E02

  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B



    B087825

  1. Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B089599E02

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B114992E01

  1. Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



25. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01

  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03

  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993

  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01

  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01

  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01

  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01

  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01

  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



26. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH


B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B084922E01

  1. w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }



    B113098E03

  1. w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B



    B114993

  1. w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.



    B084915E01

  1. Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.



    B084920E01

  1. Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.



    B085691E01

  1. Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085692E01

  1. Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B085693E01

  1. Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



27. INSTALL REAR SEATBACK ASSEMBLY


    B108088E01

  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the seatback's 2 hooks to the vehicle body.

  1. Install the seat with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 in.*lbf }



28. INSTALL BACK PANEL GARNISH LOWER


B085704E01

  1. Attach the 5 clips and 6 claws to install the garnish.



29. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    B115404E02

  1. Attach the seat cushion's 2 rear hooks to the vehicle body.



    B115402E01

  1. Attach the seat cushion's front hook to the rear seat cushion lock hook. Then install the seat cushion.

  1. Confirm that the seat cushion is firmly installed.



30. INSTALL REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



31. INSTALL BACK PANEL GARNISH UPPER


B086202E01

  1. Attach the 5 clips and 4 claws to install the garnish.



32. INSTALL FRONT PILLAR GARNISH LH


B111746E01

  1. Attach the 2 clips and 2 claws to install the garnish.

  1. w/ Assist grip:
    Install the assist grip with the 2 screws.

  1. w/ Assist grip:
    Attach the 4 claws to install the 2 assist plugs.



33. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



34. INSTALL COWL SIDE TRIM BOARD LH


B085566E01

  1. Attach the 2 clips to install the trim board.

  1. Install the cap nut.



35. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedures described for the LH side.



36. INSTALL FRONT DOOR OPENING TRIM LH


37. INSTALL FRONT DOOR OPENING TRIM RH


38. INSTALL FRONT DOOR SCUFF PLATE LH


B085559E01

  1. Attach the 4 clips and 8 claws to install the scuff plate.



39. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.



40. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


41. PERFORM INITIALIZATION

  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.