CYLINDER HEAD > REPLACEMENT

for Preparation Click here



1. REMOVE CAMSHAFT OIL SEAL

  1. Pull out the oil seal.



2. REMOVE VALVE STEM OIL SEAL


A058955E01

  1. Using needle-nose pliers, remove the oil seal.



3. REMOVE INTAKE VALVE GUIDE BUSH


A053808E02

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).



    A059922E01

  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)



4. REMOVE EXHAUST VALVE GUIDE BUSH


A053808E02

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).



    A059923E01

  1. Using SST and a hammer, tap out the valve guide bush.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)



5. INSTALL INTAKE VALVE GUIDE BUSH


A059167E01

  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    		Bush Bore Diameter
    Use STD
    		10.985 to 11.006 mm (0.4325 to 0.4333 in.)
    Use O/S 0.05
    		11.035 to 11.056 mm (0.4344 to 0.4353 in.)

    If the bush bore diameter of the cylinder head is greater than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 to 11.056 mm (0.4344 to 0.4353 in.).
    If the bush bore diameter of the cylinder head is greater than 11.056 mm (0.4353 in.), replace the cylinder head.



    A061560E01

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)



    A059166E01

  1. Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.



6. INSTALL EXHAUST VALVE GUIDE BUSH


A059172E01

  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Select a new guide bush (STD or O/S 0.05):
    Bush Size
    		Bush Bore Diameter
    Use STD
    		10.985 to 11.006 mm (0.4325 to 0.4333 in.)
    Use O/S 0.05
    		11.035 to 11.056 mm (0.4344 to 0.4353 in.)

    If the bush bore diameter of the cylinder head is greater than 11.006 mm (0.4333 in.), machine the bush bore diameter to between 11.035 to 11.056 mm (0.4344 to 0.4353 in.).
    If the bush bore diameter of the cylinder head is greater than 11.056 mm (0.4353 in.), replace the cylinder head.



    A061559E01

  1. Gradually heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

  1. Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

    SST
    09201-10000   (09201-01060)
    09950-70010   (09951-07100)

    Protrusion height (H):
    10.3 to 10.7 mm (0.406 to 0.421 in.)



    A059170E01

  1. Using a sharp 6.0 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.



7. INSTALL VALVE STEM OIL SEAL


A059919E01

  1. Using SST, push in a new oil seal.

    SST
    09201-41020  



8. INSTALL CAMSHAFT OIL SEAL


A060145E01

  1. Install the camshaft oil seal.

    1. Apply MP grease to the lip of a new oil seal.

    2. Using SST and a hammer, tap in the oil seal until its surface is flush with the oil seal retainer edge.

      SST
      09608-06041