POWER WINDOW CONTROL SYSTEM > Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

for Preparation Click here


DESCRIPTION

If the passenger side manual UP / DOWN function does not operate, a malfunction may be present in the power window regulator motor, power window regulator switch, power window regulator master switch or wire harness.

WIRING DIAGRAM


B107968E01


INSPECTION PROCEDURE

1.CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE) (POWER SOURCE)
B107969E04

  1. Disconnect the P9 regulator switch connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    		Condition
    		Specified Condition
    P9-3 - Body ground
    		Ignition switch ON
    		10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


2.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE)
B063163

  1. Remove the switch.

  1. Measure the resistance of the switch when the switch is operated.

    Standard resistance:
    Tester Connection
    		Switch Condition
    		Specified Condition
    5 - 4
    2 - 3
    		UP
    		Below 1 Ω
    5 - 4
    2 - 1
    		OFF
    		Below 1 Ω
    5 - 3
    2 - 1
    		DOWN
    		Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (PASSENGER SIDE)
OK


3.CHECK WIRE HARNESS (SWITCH (PASSENGER SIDE) - MOTOR (PASSENGER SIDE))

B111941E02

  1. Disconnect the P9 switch connector.

  1. Disconnect the P6*1 or P5*2 motor connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    LHD
    Tester Connection
    		Specified Condition
    P9-5 - P6-1
    		Below 1 Ω
    P9-2 - P6-2
    		Below 1 Ω
    P9-5 or P6-1 - Body ground
    		10 kΩ or higher
    P9-2 or P6-2 - Body ground
    		10 kΩ or higher
    RHD
    Tester Connection
    		Specified Condition
    P9-5 - P5-1
    		Below 1 Ω
    P9-2 - P5-2
    		Below 1 Ω
    P9-5 or P5-1 - Body ground
    		10 kΩ or higher
    P9-2 or P5-2 - Body ground
    		10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)
B086400E01

  1. LHD:

    1. Remove the motor.

    2. Apply battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      		Motor gear rotates clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      		Motor gear rotates counterclockwise



    B086401E01

  1. RHD:

    1. Remove the motor.

    2. Apply battery voltage to connector terminals 1 and 2.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      		Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      		Motor gear rotates counterclockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      		Motor gear rotates clockwise



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (PASSENGER SIDE)
OK


5.CHECK WIRE HARNESS (MASTER SWITCH - SWITCH (PASSENGER SIDE))

B111940E04

  1. LHD:

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P9 switch connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Single cab, Extra cab
      Tester Connection
      		Specified Condition
      P4-8 (PU) - P9-1
      		Below 1 Ω
      P4-10 (PD) - P9-4
      		Below 1 Ω
      P4-8 (PU) or P9-1 - Body ground
      		10 kΩ or higher
      P4-10 (PD) or P9-4 - Body ground
      		10 kΩ or higher
      Double cab
      Tester Connection
      		Specified Condition
      P4-18 (PU) - P9-1
      		Below 1 Ω
      P4-15 (PD) - P9-4
      		Below 1 Ω
      P4-18 (PU) or P9-1 - Body ground
      		10 kΩ or higher
      P4-15 (PD) or P9-4 - Body ground
      		10 kΩ or higher


B111940E05

  1. RHD:

    1. Disconnect the P4 master switch connector.

    2. Disconnect the P9 switch connector.

    3. Measure the resistance of the wire harness side connectors.

      Standard resistance:
      Single cab, Extra cab
      Tester Connection
      		Specified Condition
      P4-8 (PU) - P9-1
      		Below 1 Ω
      P4-1 (PD) - P9-4
      		Below 1 Ω
      P4-8 (PU) or P9-1 - Body ground
      		10 kΩ or higher
      P4-1 (PD) or P9-4 - Body ground
      		10 kΩ or higher
      Double cab
      Tester Connection
      		Specified Condition
      P4-10 (PU) - P9-1
      		Below 1 Ω
      P4-13 (PD) - P9-4
      		Below 1 Ω
      P4-10 (PU) or P9-1 - Body ground
      		10 kΩ or higher
      P4-13 (PD) or P9-4 - Body ground
      		10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (FRONT PASSENGER SWITCH)
B112772E02

  1. LHD (Single cab, extra cab):
    Inspect the front passenger switch.

    1. Remove the master switch.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      Window Lock Switch Condition
      		Power Window Switch Condition
      		Tester Connection
      		Specified Condition
      OFF
      		UP
      		1 (E) - 10 (PD)
      8 (PU) - 9 (B)
      		Below 1 Ω
      OFF
      		OFF
      		1 (E) - 8 (PU)
      1 (E) - 10 (PD)
      		Below 1 Ω
      OFF
      		DOWN
      		1 (E) - 8 (PU)
      9 (B) - 10 (PD)
      		Below 1 Ω
      ON
      		UP
      		1 (E) - 10 (PD)
      		10 kΩ or higher
      8 (PU) - 9 (B)
      		Below 1 Ω
      ON
      		OFF
      		8 (PU) - 10 (PD)
      		Below 1 Ω
      ON
      		DOWN
      		1 (E) - 8 (PU)
      		10 kΩ or higher
      9 (B) - 10 (PD)
      		Below 1 Ω



    B085836E02

  1. RHD (Single cab, extra cab):
    Inspect the front passenger switch.

    1. Remove the master switch.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      Window Lock Switch Condition
      		Power Window Switch Condition
      		Tester Connection
      		Specified Condition
      OFF
      		UP
      		1 (PD) - 10 (E)
      8 (PU) - 9 (B)
      		Below 1 Ω
      OFF
      		OFF
      		8 (PU) - 10 (E)
      1 (PD) - 10 (E)
      		Below 1 Ω
      OFF
      		DOWN
      		8 (PU) - 10 (E)
      1 (PD) - 9 (B)
      		Below 1 Ω
      ON
      		UP
      		1 (PD) - 10 (E)
      		10 kΩ or higher
      8 (PU) - 9 (B)
      		Below 1 Ω
      ON
      		OFF
      		1 (PD) - 8 (PU)
      		Below 1 Ω
      ON
      		DOWN
      		8 (PU) - 10 (E)
      		10 kΩ or higher
      1 (PD) - 9 (B)
      		Below 1 Ω



    B059314E03

  1. LHD (Double cab):
    Inspect the front passenger switch.

    1. Remove the master switch.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      Window Lock Switch Condition
      		Power Window Switch Condition
      		Tester Connection
      		Specified Condition
      OFF
      		UP
      		3 (E) - 15 (PD)
      6 (B) - 18 (PU)
      		Below 1 Ω
      OFF
      		OFF
      		3 (E) - 18 (PU)
      3 (E) - 15 (PD)
      		Below 1 Ω
      OFF
      		DOWN
      		3 (E) - 18 (PU)
      6 (B) - 15 (PD)
      		Below 1 Ω
      ON
      		UP
      		3 (E) - 15 (PD)
      		10 kΩ or higher
      6 (B) - 18 (PU)
      		Below 1 Ω
      ON
      		OFF
      		15 (PD) - 18 (PU)
      		Below 1 Ω
      ON
      		DOWN
      		3 (E) - 18 (PU)
      		10 kΩ or higher
      6 (B) - 15 (PD)
      		Below 1 Ω



    B085831E02

  1. RHD (Double cab):
    Inspect the front passenger switch.

    1. Remove the master switch.

    2. Measure the resistance of the switch when the switch is operated.

      Standard resistance:

      Window Lock Switch Condition
      		Power Window Switch Condition
      		Tester Connection
      		Specified Condition
      OFF
      		UP
      		3 (E) - 13 (PD)
      6 (B) - 10 (PU)
      		Below 1 Ω
      OFF
      		OFF
      		3 (E) - 10 (PU)
      3 (E) - 13 (PD)
      		Below 1 Ω
      OFF
      		DOWN
      		3 (E) - 10 (PU)
      6 (B) - 13 (PD)
      		Below 1 Ω
      ON
      		UP
      		3 (E) - 13 (PD)
      		10 kΩ or higher
      6 (B) - 10 (PU)
      		Below 1 Ω
      ON
      		OFF
      		10 (PU) - 13 (PD)
      		Below 1 Ω
      ON
      		DOWN
      		3 (E) - 10 (PU)
      		10 kΩ or higher
      6 (B) - 13 (PD)
      		Below 1 Ω



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
OK

GO TO POWER WINDOWS DO NOT OPERATE AT ALL