ANTI-LOCK BRAKE SYSTEM > OPERATION CHECK

for Preparation Click here



CHECK ABS WARNING LIGHT
C108846E02

  1. When the ignition switch is turned ON, check that the ABS warning light illuminates and then turns off in approximately 3 seconds.

    HINT:
    Troubleshoot the ABS warning light circuit if the warning light remains ON or has other malfunctions.


CHECK SENSOR SIGNAL BY TEST MODE (When not using intelligent tester:)


    C108847E01

  1. Procedures for test mode:

    1. Turn the ignition switch OFF.

    2. Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

      SST
      09843-18040  

    3. Start the engine.



      4. C108848E01

    4. Check that the ABS warning light blinks as shown in the illustration.

      HINT:
      If the ABS warning light does not blink, check the ABS warning light circuit.

  2. 4WD:
    Check the deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.



    3. C108849E01

  3. 4WD:
    Check the H2 (2WD) to H4 or L4 (4WD) shift operation.

    1. Start the engine.

    2. Shift the transfer shift lever from the H2 position to the H4 or L4 position.

    3. Check that the 4WD indicator light illuminates.

    4. Shift the transfer shift lever from the H4 or L4 position to the H2 position.

    5. Check that the 4WD indicator light turns off.

      HINT:
      1. If the indicator light does not turn off when shifting the transfer into the H2 position, drive the vehicle straight ahead while accelerating or decelerating, or drive the vehicle in reverse.
      2. If a shift is left uncompleted for 30 minutes, the 4WD indicator light will begin flashing.

  4. Check the speed sensor.

    1. Drive the vehicle straight forward at the following speeds. Then check that the ABS warning light is as follows.
      Vehicle Speed
      		Check
      		ABS Warning Light
      3 to 5 km/h (2 to 3 mph)
      		Response of sensors
      		Blinking
      45 km/h (28 mph) or higher
      		Deviations of sensor signal
      		Turns off

      HINT:
      The sensor signal check may not be completed if the vehicle's wheels slip or the steering wheel is turned during this check.

    2. Stop the vehicle.



    5. C108847E02

  5. Read the DTCs.

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  



    2. Read the number of blinks of the ABS warning light.

      HINT:
      1. As an example, the blinking patterns for DTCs 72 and 76 are shown below.
      2. The conditions are explained in the Diagnostic Trouble Code Chart.
      3. For the normal code, the light cycles between ON and OFF at intervals of 0.25 seconds.
      4. If more than 1 DTC is detected at the same time, the codes will be displayed in numerical order.


      C108851E01

  6. After the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.


CHECK SENSOR SIGNAL BY TEST MODE (When using intelligent tester:)


    C108852E01

  1. Procedures for test mode:

    1. Turn the ignition switch OFF.

    2. Check that the shift lever is on P.

    3. Connect the intelligent tester to the DLC3.

    4. Start the engine.

    5. Select the Test Mode using the intelligent tester.

      HINT:
      Refer to the intelligent tester operator's manual for further details.



      6. C108848E01

    6. Check that the ABS warning light blinks.

      HINT:
      If the ABS warning light does not blink, check the ABS warning light circuit.

    7. Start the engine.

  2. 4WD:
    Check the deceleration sensor.

    1. Keep the vehicle stationary on a level surface for 1 second or more.



    3. C108849E01

  3. 4WD:
    Check the H2 (2WD) to H4 or L4 (4WD) shift operation.

    1. Start the engine.

    2. Shift the transfer shift lever from the H2 position to the H4 or L4 position.

    3. Check that the 4WD indicator light illuminates.

    4. Shift the transfer shift lever from the H4 or L4 position to the H2 position.

    5. Check that the 4WD indicator light turns off.

      HINT:
      1. If the indicator light does not turn off when shifting the transfer into the H2 position, drive the vehicle straight ahead while accelerating or decelerating, or drive the vehicle in reverse.
      2. If a shift is left uncompleted for 30 minutes, the 4WD indicator light will begin flashing.

  4. Check the speed sensor.

    1. Drive the vehicle straight forward at the following speeds. Then check that the ABS warning light is as follows.
      Test
      		Check
      		ABS Warning Light
      3 to 5 km/h (2 to 3 mph)
      		Response of sensors
      		Blinking
      45 km/h (28 mph) or higher
      		Deviations of sensor signal
      		Turns off

      HINT:
      The sensor signal check may not be completed if the vehicle's wheels slip or the steering wheel is turned during this check.

    2. Stop the vehicle.

  5. Read the DTC(s).

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON.

    3. Read the DTCs by following the prompts on the tester screen.