OIL PUMP > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. Even after discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



    G038856E01

  1. Disconnect the fuel pump connector.

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch OFF.

    HINT:
    DTC P0171/25 (system too lean) may be set.

  1. Crank the engine again, then check that the engine does not start.

  1. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump connector.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at leat 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



3. REMOVE ENGINE ASSEMBLY

  1. Remove the engine from the vehicle (Click here).



4. REMOVE DRIVE PLATE AND RING GEAR ASSEMBLY (for Automatic Transmission)


A076326E01

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A076327E01

  1. Remove the 8 bolts, front spacer, drive plate and rear spacer.

    NOTICE:
    Do not reuse the bolts.



5. REMOVE FLYWHEEL (for Manual Transmission)


A076326E01

  1. Using SST, hold the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A076899E01

  1. Remove the 8 bolts and flywheel.

    NOTICE:
    Do not reuse the bolts.



6. INSTALL ENGINE ASSEMBLY TO STAND


7. REMOVE OIL DIPSTICK GUIDE

  1. Remove the oil dipstick.

  1. Remove the bolt and pull out the oil dipstick guide.

  1. Remove the O-ring from the oil dipstick guide.



8. REMOVE WATER INLET


    A112082

  1. Remove the 3 nuts, water inlet with thermostat and gasket.



9. REMOVE GENERATOR


A112761

  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts, adjusting bar and generator.



10. REMOVE V-RIBBED BELT TENSIONER


A076445E01

  1. Remove the 5 bolts and V-ribbed belt tensioner.



11. REMOVE NO. 2 IDLER PULLEY

  1. Remove the 2 bolts and 2 idler pulleys.



12. REMOVE NO. 1 IDLER PULLEY

  1. Remove the bolt and idler pulley.



13. REMOVE CRANKSHAFT PULLEY


    A072945E01

  1. Turn the crankshaft pulley, and align its groove with the timing mark 0 of the timing chain cover.



    G038065E03

  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as above.



    A072947E01

  1. Using SST, hold the crankshaft pulley and loosen the pulley set bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E01

  1. Using the pulley set bolt and SST, remove the crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05030)



14. REMOVE NO. 2 OIL PAN


    A112956E01

  1. Remove the 10 bolts and 2 nuts.



    A112957E01

  1. Insert the blade of SST between the oil pan and No. 2 oil pan, cut through the applied sealer and remove the No. 2 oil pan.

    SST
    09032-00100  

    NOTICE:
    1. Be careful not to damage the contact surfaces of the oil pan and No. 2 oil pan.
    2. Be careful not to damage the No. 2 oil pan flange.



15. REMOVE OIL STRAINER


    A112955

  1. Remove the bolt, 2 nuts, oil strainer and gasket.



16. REMOVE NO. 1 OIL PAN


    A112952E02

  1. Remove the 17 bolts and 2 nuts.



    A112954

  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

  1. Remove the O-ring from the oil pump.



17. REMOVE IGNITION COIL


18. REMOVE CYLINDER HEAD COVER RH


    A072943E01

  1. Remove the 10 bolts, 3 seal washers, 2 nuts, head cover and gasket.



19. REMOVE CYLINDER HEAD COVER LH


    A072944E01

  1. Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.

  1. Remove the ventilation valve from the cylinder head cover.



20. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE

  1. Disconnect the 2 oil control valve connectors.

  1. Remove the 2 bolts and 2 oil control valves.



21. REMOVE VVT SENSOR


    G038105

  1. Disconnect the sensor connector.

  1. Remove the bolt and sensor.



22. REMOVE OIL FILTER BRACKET

  1. Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.



23. REMOVE TIMING CHAIN COVER


    G038101E02

  1. Remove the 24 bolts and 2 nuts.



    G038102E01

  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

  1. Remove the O-ring from the LH cylinder head.



24. REMOVE TIMING CHAIN COVER OIL SEAL

  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil pump body. Tape the screwdriver before use..