DTC    P2119    Throttle Actuator Control Throttle Body Range / Performance

for Preparation Click here


DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, throttle position sensor, the accelerator pedal position sensor and ECM.
This system is the one valve type throttle body.
In order to the proper opening angle of the throttle valve in response to driving conditions, the throttle position sensor mounted on the throttle body detects the actual throttle valve opening angle. Then the sensor provides feedback to the ECM so that the ECM can control the actuator.
If the ETCS has a malfunction, the ECM shuts down the power for the actuator, and the throttle valve is locked at a certain angle by the return spring. Also, all electronically controlled throttle operations are canceled until the system returns to normal and ignition switch is turned OFF.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle valve opening angle continues to vary greatly from target throttle opening angle
  1. ETCS
  1. ECM

MONITOR DESCRIPTION

The ECM determines the "actual" throttle angle based on the throttle position sensor signal. The "actual" throttle position is compared to the "target" throttle position commanded by the ECM. If the difference of these 2 values exceeds a specified limit, the ECM interprets this as a fault in the ETCS system. The ECM illuminated the Malfunction Indicator Lamp (MIL) and sets the DTC.
Start the engine, fully depress the accelerator pedal until the engine reaches 5,000 rpm (to fully open the throttle valve), and quickly release the accelerator pedal (to close the throttle valve).

FAIL-SAFE

If the ETCS is malfunctioning, the ECM cuts off the current to the throttle actuator. The throttle control valve returns to a predetermined throttle position (approximately 6°) by the force of the return spring.
Then, required engine power is calculated using the ignition timing and accelerator pedal position. The engine is controlled by intermittent fuel-cut.
If the accelerator pedal is depressed firmly and slowly, the vehicle can be driven at minimum speed. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

WIRING DIAGRAM

Refer to DTC P2102 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2119)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC output)
    		Proceed to
    P2119
    		A
    P2119 and other DTCs
    		B

    HINT:
    If any other DTCs besides P2119 are output, perform troubleshooting for those DTCs first.



B
GO TO RELEVANT DTC CHART
A


2.CHECK IF DTC OUTPUT RECURS (DTC P2119)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Allow the engine to idle for 15 seconds.

    CAUTION:
    It is extremely important to confirm that the parking brake is properly applied and that the brake pedal is firmly depressed.

  1. Securely apply the parking brake and move the shift lever to drive position.

  1. While depressing the brake pedal securely, fully depress the accelerator pedal for 5 seconds.

HINT:
The output voltage of the throttle position sensor can be checked using the intelligent tester.

  1. On the tester, enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    OK:
    No DTC output.



NG
REPLACE THROTTLE BODY ASSEMBLY
OK

NORMAL