AISIN
Hubs - Identification and Rebuilding Guide.

Author: Eric Johnson - mailto:[email-masked]?Subject=Feeback
on AISIN hub guide  May 1999

Related
Links

Toyota Automatic
Differential Disconnect System

Replacing Toyota
Auto Hubs

The Toyota
Section

The Suzuki
Section

The Isuzu
Section

When we think of all the manufacturers who make locking freewheel hubs
for 4x4s, some big names come to mind: Warn, Milemarker, and Superwinch.
But one manufacturer's hubs are probably on more vehicles worldwide that
these familar makes combined: AISIN. These hubs have appeared as original
equipment on 4x4s from Toyota, Mitsubishi, Isuzu, Chevy, Dodge, Mazda, and
Suzuki.

Aisin Seiki is a japanese manufacturing company that makes everything
from auto parts to sewing machines to a temperature sensing "shower toilet
seat". While I've never tried this latter product (and don't intend to!),
their hubs are first-rate.

The hubs have a lot going for them. Their compact size -- about 2 1/4
inches deep -- means they stick out less than most aftermarket hubs, and
therefore are less likely to get hit on rocks than deeper aftermarket
hubs. The construction is solid: Forty-one of its forty-six parts are made
of steel. Two parts (the cap and dial) are aluminum, and the other three
are gaskets of various materials. The reputation of these hubs is stellar
- I've seen a lot of hubs break on the trail, but never an AISIN.

These hubs do have their downsides. The part count is daunting, though
30 of the parts are simply washers, bolts, and nuts. The assembly,
particularly the alignment of the tension spring, is challenging. Good
luck figuring out how to put one together for the first time if you don't
have a factory manual. And if you do manage to break one, new ones are
usually hundreds of dollars apiece. The most common complaint, however, is
the difficulty of removing the AISIN hubs from the wheel hubs. There are
cone-shaped washers that, when installed, are compressed over the studs in
the wheel hubs. This makes for a very solid mating of the parts, but these
washers can be very difficuly to remove. Later in this article we'll show
you a few tricks to make it easier.

AISIN hubs generally come on imported trucks, and their owners are
accustomed to paying inflated prices for replacement parts. But there is
some good news - used AISIN hubs are easily and inexpensively rebuildable
to like-new condition. And many of the parts are interchangeable between
hubs from differing vehicles. For example, you can use a junkyard hub from
a Toyota for parts to repair a Suzuki.

I obtained four different flavors of AISIN hubs for this article.
Clockwise from top-left in the picture are hubs from an IFS Toyota
4Runner, a solid axle Toyota pickup, a 1993 Isuzu Amigo, and one from a
Suzuki Samurai, Of these four, the Isuzu was the odd duck - the hub body
was much smaller overall (with a different bolt pattern) than the others,
it doesn't use cone washers for mounting, and the dial is built in such a
way to reduce the extent of the travel of the clutch. The factors combine
to make this hub a very compact unit. Still, the clutch, pawl, springs,
and other parts are compatible with the other hubs.

The Suzuki and 30-spline Toyota hubs are virtually identical except for
the inner hub. The grips on the dial of the 30-spline Toyota hub stick out
slightly beyond the cap, where on the others, it is flush. Functionally,
the dials are interchangeable between the Suzuki and 26- and 30-spline
Toyota hubs. The 26-spline (IFS) Toyota hub has a deeper backspacing
between the mounting flange and the inner hub than the other hubs, in
order to clear the spindle nuts. Because of this, the Suzuki or 30-spline
Toyota hub body will not fit on an IFS toyota wheel hub, but the reverse
should work; i.e. a 26-spline Toyota hub body should be usable on a Suzuki
or 30-spline Toyota hub.

Theory of operation:

The part of the
hub that actually engages the front driveshaft is called the inner hub. It
is sized appropriately for the diameter and spline count of the axle being
used, and is the major part that is different between hubs intended for
different vehicles. When disengaged, the inner hub, attached to the axle,
spins freely (or rather, stays put while the wheel spins around it) in the
free wheeling hub ring, which is a piece of steel with a brass bearing
surface, that centers the axle in the hub.

The outside of the inner hub has 22 splines. When the dial of the hub
is set to the LOCK position, a steel clutch with 22 internal splines is
pressed inward, engaging the splines of the inner hub. The clutch itself
slides in the thick splines of the hub body, so that when engaged, the
inner hub cannot rotate relative to the hub body. Torque from the axles is
therefore transmitted through the inner hub, the clutch, and into the hub
body. The body is securely bolted to the six studs on the wheel hub,
finishing the torque transfer from the axle to the wheels.

When disengaged, the clutch is pulled outward from the inner hub. This
allows the inner hub to rotate independently of the rest of the hub and
wheel.

Procedures for a rebuild:

Removing the hub from
the wheel
If your front wheels do not have sleeves covering
the hubs, you don't even need to remove the wheel. I suggest ditching the
sleeves anyways since they tend to trap water.

Make sure the dial is set to the "FREE" position. Remove the 6 cap
bolts with a 10mm socket. Slide out the cap and clutch assembly. Note if
there is excessive water, rust, or oil inside.

In some applications, you'll now need to remove a nut and washer at the
end of the axle. In others, there may be a snap ring or other retention
device.

With a 12mm socket, remove the 6 nuts holding on the hub body. Remove
the 6 flat washers. The cone washers will be still holding the hub
tightly. Its nice to know the hub will still hang on if a fastener falls
off on the trail!

Maybe you'll be lucky and the cone washers will wiggle right out. More
likely, they will need persuasion. The best way is to essentially vibrate
them enough so they pop up far enough to grab with needle-nose pliers.
This can be accomplished in several ways. One method is to find a socket
with an inside diameter greater that the washers. Slip it over the end of
the stud, and tap in gently with a hammer, being careful not to mar the
hub body.

This is often the only encouragement the washers need. If gentle
tapping doesn't work, spray a little pentrating oil on the washers, and
hit the socket harder. A large brass punch can be held directly against
the studs and whacked good with a hammer. Brass is soft enough to prevent
damaging the studs or hub, but hard enough to transmit the shock loads we
need. If that still doesn't work, put the nuts back on the studs, with
just enough turns so they stay at the ends of the threads, then using the
hammer and brass punch, beat on the hub body in various places. This can
be so effective that the washers will literally fly off the studs. The
nuts we slightly threaded on the end of the studs will prevent
this.

Related
Links

Toyota
Front Wheel Bearing Servicing and Replacement

With the hub off, its a fine time to to
inspect and/or repack your wheel bearings. If you saw any signs of water
inside the hub, you should plan on a repack. Water can get in via
poorly-sealed gaskets on the hub. But it can also arrive through the
spindle, For examples, on IFS Toyotas, sometimes water can get in between
the outer CV joint and spindle. It then travels through the spindle and
into the hub, where it rusts the hub and destroys the outer wheel
bearings.

Wipe out any excess grease from the hub body assembly and hub cap
assembly.

Disassembly of hub body
The hub
body assembly consists of 6 parts: The hub body itself, the inner hub, the
free wheeling hub ring, a washer between the hub ring and the hub body,
and two lock rings. Remove the large inside lock ring near the base of the
hub body, and slide out the inner hub, hub ring, and washer. Remove the
smaller outside lock ring to separate these parts from each other.

Disassembly of cap
While gripping
the dial with one hand, with the other hand press the clutch against the
cap and turn counter-clockwise, in the manner you would open a child
safety cap on a bottle of medicine. Note that there are two springs of
similar diameter. This is normal, but the two springs are sometimes
mistaken as one broken spring. Separate the springs from the pawl and
clutch, carefully noting their alignment for future installation.

The springs are the parts that actually move the clutch in and out.
When you turn the dial to the LOCK position, the compression spring is
free to press the clutch in, as soon the the splines on the inner hub and
clutch line up. Conversely, when the dial is set to "free", the tension
spring pulls on the clutch, which moves as soon as any bindup is relieved.

To take apart the cap itself, remove the single lock ring beneath the
cap. Now, carefully press the dial inward. Inside the dial betneath the
indicator arrow is a tiny spring and ball that engages detents in the cap.
Don't lose these. Carefully pry off the rubber o-ring around the dial.

Cleaning
We've now completely
detail-stripped the hub. wipe off any excess grease and clean the parts
individually. I like to use mineral spirits in a metal can to soak these
parts. Harbor Freight Tools sells an inexpensive parts cleaning can
(#35400) with a lid and a spring-loaded parts tray that is the perfect
size for cleaning hubs, but a large coffee can will work. I like to let
all the parts (except the o-ring) soak for at least a few hours. Using a
toothbrush or parts cleaning brush, try to get all the gunk off of all the
surfaces.

If you don't like dealing with solvents, a good cleaning with soap and
water and engine degreaser can be effective. If you go this route, be sure
to let everything dry thoroughly and then spray a light coat of WD-40 or
gun oil on the parts to avoid any rusting.

If there is any rust in the parts, it is often just minor surface rust
that can be removed with steel wool or wet/dry sandpaper. Minor pitting is
OK, but if there is deep corrosion in the inner hub or clutch, you might
want to consider getting another hub to use for parts.

A fresh coat of paint on the cap and dial can really make an old hub
look brand new. Any color is fine, time to be creative. I've been painting
my rebuilds black with a blue dial. Be sure to mask the inside of the cap
and outside of the dial to prevent paint from getting on the seal
surfaces. Several coats will last better than one. You can sand down the
high points to make the pointers and words appear in bright aluminum
against your background colors. I've never painted the usually-chrome hub
bodies, but I can't think of a reason it wouldn't work.

Reassembly
Inspect your hub body.
Sometimes the cap surface isn't flat because the hub has been beat against
a rock. Flatten it out with a file to assure a good cap seal.

Assemble the hub body / inner hub assembly in the reverse of the method
you used to disassemble. Apply a coating of grease on all contact surfaces
- the bronze surface where the inner hub engages the free wheeling hub
ring, both sides of the washer between the two parts, and the inner and
outer splines of the inner hub. Here and elsewhere in the hub, don't use
too much grease. We need to lubricate these surfaces to guard against
friction and moisture, but we don't need to 'pack' the hub. I've opened up
several hubs where there was so much grease it actually interfered with
the operation of the hub.

Inspect the rubber o-ring seal. If it is cracked or otherwise damaged,
replace it with a new one. Lightly coat the o-ring in grease, and slip it
over the dial. Carefully insert the spring and ball inside the dial, and
slide the dial into the cap. Make sure the pointer is between the FREE and
LOCK positions. Turn the dial between these positions, making sure you
here a click as it engages each position. When you're satisfied with the
operation, install the lock ring. Set the dial to "FREE".

Using a cotton swab or similar tool, coat the diagonal ramps in the
dial with grease. You don't need to be as stingy here - the pawl slides
against this surface as the dial is turned, so good lubrication here will
assume smooth function. Well-lubricated o-ring and ramps can really make
the difference between a hub that simply works and one that is really
smooth and easy to use.

Assembly of the clutch and tension
spring
Lubricate the inner and outer splines of the clutch.
Now comes the tricky part that always has me running for the factory
manual. The tension spring holds the pawl to the clutch and is tricky to
align properly. The end without the bend snakes into grooves in the
clutch, until the end lines up with the gap in the clutch (see
picture).
The end with the bend is also
tricky. There are two tall and two short tabs in the pawl. The bend in the
spring wraps just under one of the tall tabs, over a short tab, under the
other tall tab, and over the other short tab, then down to the clutch. See
the picture. It can be very tricky getting it all to line up correctly.
When the spring is properly aligned on the pawl, double check to see that
it hasn't slipped out of position on the clutch.

We're done with the hardest part. Slip the large compression spring
over the pawl, and press-and-turn the clutch/pawl/spring assembly into the
grooves of the dial in the FREE position. Rotate the clutch and pawl up
the ramps of the dial so that they are tight against the cap.

Note that the pawl has tabs that cross the gap between some of the
splines of the clutch. Align these tabs with the wide splines in the hub
body, and slip on the cap assembly to the hub body. Temporarily install
two opposite cap bolts. We want to test functioning.

With the dial still in the FREE position, verify you can, from the base
of the hub, turn the inner hub relative to the hub body. Now, switch the
hub to the LOCK position. If you can't turn it all the way, something is
wrong - remove the cap and check the alignment of everything. If it works
correctly, you'll hear a little click as the ball in the dial engages the
detents in the cap. Depending on the relative position of the splines of
the clutch relative to the inner hub, you may or may not hear a louder
noise of these parts engaging.

Now, try to turn the inner hub relative to the hub body. If the splines
happened to engage perfectly when you turned the dial, you will not be
able to turn the inner hub. If they didn't engage right away, you'll be
able to turn the hub a very small amount before the springs slam the
clutch into postion. Either situation is ok, as long as the inner hub
locks relative to the body. Turn the dial back to FREE. Verify that the
inner hub is now free to turn.

Remove any remaining gasket material on the wheel hub and install a new
gasket. Some RTV sealant will work in place of a gasket, but I always use
the proper gasket if its available. Install the hub body, cone washers,
flat washers, and nuts. Some anti-sieze compound on the studs and cone
washers will make later disassembly much easier. Use a star-shaped order
in tightening the bolts (like you would on a wheel) to ensure even
seating. Torque the nuts to 23 ft lbs.

If your application requires it, install the nut and washer at the end
of the axle, or whatever retention mechanism is on your axle.

Install the cap assembly and a new gasket as we did before. I like to
jack up the wheel and test operation on the vehicle. If everything still
checks out, torque the cap bolts to 7 ft-lbs.

Maintenance:

The hubs don't really require any regular
maintenance. Water is the number one enemy of your hubs and your front
wheel bearings, so after any excursion where you forded water deep enough
to submerge the hubs, its a good idea to pop off the cap and see if water
got inside. If so, repack the wheel bearings and clean and lubricate the
parts of the hub.

Back to the Toyota
section

SCORE Baja 1000
November 16-20, 2004

SEMA 2004
November 2-5,
2004

UROC SuperCrawl III at Salt Lake City,
UT
October 14-17, 2004

[ Search | Off Road
Marketplace | Main Page]
[ About | Staff |
Privacy Policy | Advertising
]
[ Classified Ads |
Message
Boards ]

Don't Ask! • Checkpoint • Wanderers • Woman
Overbored

• Jeep • DirtBike • RaceDesert.com • Land Use Issues •
• Rock-Crawling.com • ATV •
Snowmobile •
• Ford • Dodge • Chevy • Hummer • Sandsports • Suzuki •
• Toyota • Nissan • RC Cars • Outdoors •
• Baja.net • Important Disclaimers
•

Copyright ©
1995-2004, Off-Road.com a publication of the Rubicon media Group, Inc.
All
rights reserved. All contents making up this page are protected by
United States copyright and other intellectual property laws and may not
be reproduced, rewritten, distributed, redisseminated, transmitted,
displayed, published or broadcast, directly or indirectly, in any medium
without
the prior written permission of Rubicon Media Group,
Inc.