FORESTER 20MY PubNo: G8270BE Version: 006

ILLUSTRATION	TOOL NUMBER	DESCRIPTION	REMARKS
	—	SUBARU SELECT MONITOR 4	Used for setting of each function and troubleshooting for electrical system. For detailed operation procedures, refer to “Help” of application.

TOOL NAME	REMARKS
Circuit tester	Used for measuring resistance, voltage and current.
DST-i	Used together with Subaru Select Monitor 4.

POWER SEAT MEMORY(DIAGNOSTICS) > Control Module I/O Signal　

ELECTRICAL SPECIFICATION

1. Power Seat & Remote Control Mirror CM

Terminal No.	Contents	Measuring condition	Standard	Note
(R502) No. 1 ←→ Chassis ground	Mirror load drive power supply	Always	9.0 — 16 V	-
(R502) No. 2 ←→ Chassis ground	ECM power supply	Always	9.0 — 16 V	-
(R502) No. 3	-	-	-	-
(R502) No. 4	Remote control mirror SW power supply	When the mirror surface is operated	9.0 — 16 V	-
(R502) No. 5	Remote control mirror SW MAL input (L side)	When the mirror surface is operated (up)	10 kΩ or more	Only when the left mirror is operated
		When the mirror surface is operated (down)	10 kΩ or more	Only when the left mirror is operated
		When the mirror surface is operated (right)	1.5 V or less	Only when the left mirror is operated
		When the mirror surface is operated (left)	3.7 V or more	Only when the left mirror is operated
(R502) No. 6	Remote control mirror SW MCL input (L side)	When the mirror surface is operated (up)	3.7 V or more	Common to both the right and left mirror operation
		When the mirror surface is operated (down)	1.5 V or less	Common to both the right and left mirror operation
		When the mirror surface is operated (right)	3.7 V or more	Common to both the right and left mirror operation
		When the mirror surface is operated (left)	1.5 V or less	Common to both the right and left mirror operation
(R502) No. 7	-	-	-	-
(R502) No. 8 ←→ Chassis ground	Ignition power supply	IG ON	9.0 — 16 V	-
(R502) No. 9 ←→ Chassis ground	ACC power supply	ACC ON	9.0 — 16 V	-
(R502) No. 10 ←→ Chassis ground	ECM GND	Always	0 V	-
(R502) No. 11	-	-	-	-
(R502) No. 12	-	-	-	-
(R502) No. 13	-	-	-	-
(R502) No. 14	Remote control mirror SW MAR input (R side)	When the mirror surface is operated (up)	10 kΩ or more	Only when the right mirror is operated
		When the mirror surface is operated (down)	10 kΩ or more	Only when the right mirror is operated
		When the mirror surface is operated (right)	1.5 V or less	Only when the right mirror is operated
		When the mirror surface is operated (left)	3.7 V or more	Only when the right mirror is operated
(R502) No. 15	Remote control mirror SW MBR input (R side)	When the mirror surface is operated (up)	10 kΩ or more	Only when the right mirror is operated
		When the mirror surface is operated (down)	10 kΩ or more	Only when the right mirror is operated
		When the mirror surface is operated (right)	1.5 V or less	Only when the right mirror is operated
		When the mirror surface is operated (left)	3.7 V or more	Only when the right mirror is operated
(R502) No. 16	Remote control mirror SW MBL input (L side)	When the mirror surface is operated (up)	1.5 V or less	Only when the left mirror is operated
		When the mirror surface is operated (down)	3.7 V or more	Only when the left mirror is operated
		When the mirror surface is operated (right)	10 kΩ or more	Only when the left mirror is operated
		When the mirror surface is operated (left)	10 kΩ or more	Only when the left mirror is operated
(R502) No. 17	-	-	-	-
(R502) No. 18	LIN communication	-	Cannot be measured	-
(R502) No. 19	-	-	-	-
(R502) No. 20	-	-	-	-
(R502) No. 21	-	-	-	-
(R502) No. 22	-	-	-	-
(R502) No. 23	-	-	-	-
(R502) No. 24	-	-	-	-
(R502) No. 25	-	-	-	-
(R502) No. 26 ←→ Chassis ground	Mirror SW GND	Always	10 kΩ or more	-
(R502) No. 27	-	-	-	-
(R502) No. 28	Memory 2	Switch ON	1 V or less	-
(R502) No. 29	Memory 1	Switch ON	1 V or less	-
(R502) No. 30	Memory set	Switch ON	1 V or less	-
(R503) No. 1	Tilt motor (+)	When the motor is operated	9.0 — 16 V	-
(R503) No. 2	Tilt motor (-)	When the motor is operated	9.0 — 16 V	-
(R503) No. 3	L side mirror memory sensor input - (up/down)	Always	0 — 5.0 V	Changes when the left side mirror surface is operated in the up/down direction Down direction: 0 V — Up direction: 5.0 V
(R503) No. 4	L side mirror memory sensor input - (left/right)	Always	0 — 5.0 V	Changes when the left side mirror surface is operated in the left/right direction Right direction (inward): 0 V — Left direction (outward): 5.0 V
(R503) No. 5	Reclining motor (+)	-	-	-
(R503) No. 6	Reclining motor (-)	-	-	-
(R503) No. 7	L side mirror surface output (+)	When the mirror surface is operated (up, right)	(+B voltage) - 1.2 V or more	-
(R503) No. 7	L side mirror surface output (+)	When the mirror surface is operated (down, left)	0.7 V or less	-
(R503) No. 8	L side mirror surface output (up/down)	When the mirror surface is operated (up)	0.7 V or less	-
(R503) No. 8	L side mirror surface output (up/down)	When the mirror surface is operated (down)	(+B voltage) - 1.2 V or more	-
(R503) No. 9	L side mirror surface output (left/right)	When the mirror surface is operated (right)	0.7 V or less	-
(R503) No. 9	L side mirror surface output (left/right)	When the mirror surface is operated (left)	(+B voltage) - 1.2 V or more	-
(R503) No. 10	L side mirror memory sensor power supply	Always	5.0 V	-
(R503) No. 11	R side mirror memory sensor input (up/down)	Always	0 — 5.0 V	Changes when the right side mirror surface is operated in the up/down direction Down direction: 0 V — Up direction: 5.0 V
(R503) No. 12	R side mirror memory sensor input (left/right)	Always	0 — 5.0 V	Changes when the right side mirror surface is operated in the left/right direction Right direction (outward): 5.0 V — Left direction (inward): 0 V
(R503) No. 13	L side mirror memory sensor GND	Always	1 Ω or less	-
(R503) No. 14	-	-	-	-
(R503) No. 15	-	-	-	-
(R503) No. 16	-	-	-	-
(R503) No. 17	R side mirror surface motor output (left/right)	When the mirror surface is operated (right)	(+B voltage) - 1.2 V or more	-
(R503) No. 17	R side mirror surface motor output (left/right)	When the mirror surface is operated (left)	(+B voltage) - 1.2 V or more	-
(R503) No. 18	R side mirror surface motor output (up/down)	When the mirror surface is operated (up)	0.7 V or less	-
(R503) No. 18	R side mirror surface motor output (up/down)	When the mirror surface is operated (down)	(+B voltage) - 1.2 V or more	-
(R503) No. 19	R side mirror surface motor output (+)	When the mirror surface is operated (up, right)	(+B voltage) - 1.2 V or more	-
(R503) No. 19	R side mirror surface motor output (+)	When the mirror surface is operated (down, left)	0.7 V or less	-
(R503) No. 20	R side mirror memory sensor power supply	Always	5.0 V	-
(R503) No. 21	R side mirror memory sensor GND	Always	1 Ω or less	-
(R503) No. 22	-	-	-	-
(R503) No. 23	-	-	-	-
(R503) No. 24	-	-	-	-
(R504) No. 1	Seat motor drive power supply	Always	9.0 — 16 V	-
(R504) No. 2	ECM GND	Always	1 Ω or less	-
(R504) No. 3	Slide motor (+)	When the motor is operated	9.0 — 16 V	-
(R504) No. 4	Slide motor (-)	When the motor is operated	9.0 — 16 V	-
(R504) No. 5	Lifter motor (+)	When the motor is operated	9.0 — 16 V	-
(R504) No. 6	Lifter motor (-)	When the motor is operated	9.0 — 16 V	-
(R504) No. 7	Slide switch (+)	Switch ON	1.5 V or less	-
(R504) No. 8	Tilt switch (+)	Switch ON	1.5 V or less	-
(R504) No. 9	Reclining switch (+)	Switch ON	1.5 V or less	-
(R504) No. 10	Lifter switch (+)	Switch ON	1.5 V or less	-
(R504) No. 11	-	-	-	-
(R504) No. 12	Seat pulse sensor GND	Always	1 Ω or less	-
(R504) No. 13	-	-	-	-
(R504) No. 14	-	-	-	-
(R504) No. 15	Tilt pulse	When the motor is operated	Pulse input	-
(R504) No. 16	-	-	-	-
(R504) No. 17	Lifter pulse	When the motor is operated	Pulse input	-
(R504) No. 18	Slide switch (-)	Switch ON	1.5 V or less	-
(R504) No. 19	Tilt switch (-)	Switch ON	1.5 V or less	-
(R504) No. 20	Reclining switch (-)	Switch ON	1.5 V or less	-
(R504) No. 21	Lifter switch (-)	Switch ON	1.5 V or less	-
(R504) No. 22	Seat motor pulse sensor power supply	Always		-
(R504) No. 23	-	-	-	-
(R504) No. 24	Reclining pulse	When the motor is operated	Pulse input	-
(R504) No. 25	-	-	-	-
(R504) No. 26	Slide pulse	When the motor is operated	Pulse input	-

POWER SEAT MEMORY(DIAGNOSTICS) > Inspection Mode　

PROCEDURE

It is possible to diagnose the DTC by performing the indicated inspection mode. After correcting the DTC, perform a necessary inspection mode and make sure that the function is resumed correctly and the DTC is recorded.

1. INSPECTION MODE 1

DTC	Item	Note
B2600	LIN Communication	—
B2601	LIN Circuit Low	—
B2602	Vehicle Speed Control	—
B2603	EPB Control	—
B2605	Battery Control Low	—
B2609	IG	—
B260A	ACC	—
B2621	MIRROR SW ANOMALOUS STATE	—
B2632	MIRROR D SENSOR CIRCUIT ANOMALOUS STATE	—
B2642	MIRROR P SENSOR CIRCUIT ANOMALOUS STATE	—

Diagnostic procedure:

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

After solving the DTC, repeat from step 1).

Turn the ignition switch ON → OFF, and wait for 45 seconds or more.

Turn the ignition switch OFF → ON, and wait for 5 seconds or more.

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

2. INSPECTION MODE 2

DTC	Item	Note
B2604	Power Seat Memory EEPROM	—

Diagnostic procedure:

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

After solving the DTC, repeat from step 1).

Initialize the power seat system. SEATS>Power Seat System

Turn the ignition switch ON → OFF, and wait for 45 seconds or more.

Turn the ignition switch OFF → ON, and wait for 5 seconds or more.

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

3. INSPECTION MODE 3

DTC	Item	Note
B2606	Power Seat Position Sensor Circuit low	—

Diagnostic procedure:

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

After solving the DTC, repeat from step 1).

Operate the power seat switch. (Any of slide/reclining/lifter/tilt)

Turn the ignition switch ON → OFF, and wait for 45 seconds or more.

Turn the ignition switch OFF → ON, and wait for 5 seconds or more.

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

4. INSPECTION MODE 3

DTC	Item	Note
B2631	MIRROR D MOTOR CIRCUIT ANOMALOUS STATE	—
B2641	MIRROR P MOTOR CIRCUIT ANOMALOUS STATE	—

Diagnostic procedure:

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

After solving the DTC, repeat from step 1).

Turn the ignition switch to ON.

Operate the appropriate switch.

Using the Subaru Select Monitor, read the DTC of [Power Seat Memory] to check that there is no DTC displayed. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

If the DTC is displayed on the screen, the trouble is still present. Perform the diagnosis for the displayed DTCs.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure for Subaru Select Monitor Communication　

INSPECTION

Detecting condition:

Defective harness
Power supply circuit malfunction
Power Seat & Remote Control Mirror CM malfunctioning
Body integrated unit malfunctioning
Defective LIN communication circuit
Defective Subaru Select Monitor

Trouble symptom:

Not communicable with Subaru Select Monitor.

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

If the communication with the body integrated unit is not possible either, refer to BODY CONTROL SYSTEM (DIAGNOSTICS). LAN SYSTEM (DIAGNOSTICS)>Diagnostic Procedure for Subaru Select Monitor Communication>INSPECTION

1. CHECK OTHER COMMUNICATION.

Communicate with the system other than [Power Seat Memory] using the Subaru Select Monitor.

Is the communication to other control module possible?

Perform the “Communication for Initializing Impossible” of LAN system. LAN SYSTEM (DIAGNOSTICS)>Basic Diagnostic Procedure>PROCEDURE

2. CHECK LAN SYSTEM.

Perform the inspection for LAN system. LAN SYSTEM (DIAGNOSTICS)>Basic Diagnostic Procedure>PROCEDURE

Is the check result OK?

Perform the diagnosis according to the inspection for LAN system.

3. CHECK FOR POOR CONTACT.

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the connector of body integrated unit.

Connect the disconnected connectors.

Turn the ignition switch to ON.

Communicate with [Power Seat Memory] using the Subaru Select Monitor.

Is communication possible?

The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

4. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 2 (+) — Chassis ground (−):

(R502) No. 8 (+) — Chassis ground (−):

(R502) No. 9 (+) — Chassis ground (−):

Is the voltage 9 — 16 V?

Repair the open circuit of the harness between Power Seat & Remote Control Mirror CM connector and the fuse.

5. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 10 — Chassis ground:

(R504) No. 2 — Chassis ground:

Is the resistance less than 1 Ω?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Repair the open circuit in harness between Power Seat & Remote Control Mirror CM connector and chassis ground.

POWER SEAT MEMORY(DIAGNOSTICS) > Data Monitor　

OPERATION

For detailed operation procedures, refer to “Common (Diagnostics)”. COMMON(diag)>Data Monitor
For details on the data monitor, refer to the list. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor>LIST

POWER SEAT MEMORY(DIAGNOSTICS) > Data Monitor　

LIST

Display	Contents	Standard	Note
Battery Voltage	Battery voltage is displayed.	0 — 25.5 V	—
Ignition SW	Ignition switch status is displayed.	ON: When the ignition switch is ON OFF: When the ignition switch is OFF	—
Set SW	Status of the set switch in seat memory switch is displayed.	ON: When set switch is ON OFF: When set switch is OFF	—
Memory SW1	Status of the memory switch 1 in seat memory switch is displayed.	ON: When memory switch 1 is ON OFF: When memory switch 1 is OFF	—
Memory SW2	Status of the memory switch 2 in seat memory switch is displayed.	ON: When memory switch 2 is ON OFF: When memory switch 2 is OFF	—
Slide SW	Status of the slide switch in power seat switch is displayed.	OFF: When slide switch is OFF FRONT: When slide switch (forward) is ON REAR: When slide switch (rearward) is ON	—
Reclining SW	Status of the reclining switch in power seat switch is displayed.	OFF: When reclining switch is OFF FRONT: When reclining switch (forward) is ON REAR: When reclining switch (backward) is ON	—
Lifter SW	Status of the lifter switch in power seat switch is displayed.	OFF: When lifter switch is OFF UP: When lifter switch (up) is ON DOWN: When lifter switch (down) is ON	—
Tilt SW	Status of the tilt switch in power seat switch is displayed.	OFF: When tilt switch is OFF UP: When tilt switch (up) is ON DOWN: When tilt switch (down) is ON	—
Pulse Power Circuit	Motor pulse sensor power supply circuit status is displayed.	Normal: At normal condition Abnormal: Abnormal	—
Slide Output	Power seat control module output status is displayed. (Slide motor)	OFF: When set to OFF FRONT: When moved forward REAR: When moved rearward	—
Reclining Output	Power seat control module output status is displayed. (Reclining motor)	OFF: When set to OFF FRONT: When moved forward REAR: When moved rearward	—
Lifter Output	Power seat control module output status is displayed. (Lifter motor)	OFF: When set to OFF UP: When moved upward DOWN: When moved downward	—
Tilt Output	Power seat control module output status is displayed. (Tilt motor)	OFF: When set to OFF UP: When moved upward DOWN: When moved downward	—
Memory SW1 Memorized	Registration status of the memory switch 1 in seat memory switch	Yes: When registered No: When not registered	—
Memory SW2 Memorized	Registration status of the memory switch 2 in seat memory switch	Yes: When registered No: When not registered	—
Keyless Access & Start Link 1 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered	Seat memory operates when the key No. displayed in the Keyless Access Key Information is registered in the item shown on the left.
Keyless Access & Start Link 2 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access & Start Link 3 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access & Start Link 4 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access & Start Link 5 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access & Start Link 6 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access & Start Link 7 Memorized	Registration status of keyless access key	Yes: When registered No: When not registered
Keyless Access Key Information	Key No. currently identified by the vehicle is displayed.	Without: When there is no registered key Keyless Access & Start Link 1: Keyless Access & Start Link 2: Keyless Access & Start Link 3: Keyless Access & Start Link 4: Keyless Access & Start Link 5: Keyless Access & Start Link 6: Keyless Access & Start Link 7:	—
Slide Position	Slide motor position is displayed.	−32768 — 32767	—
Reclining Position	Reclining motor position is displayed.	−32768 — 32767	—
Lifter Position	Lifter motor position is displayed.	−32768 — 32767	—
Tilt Position	Tilt motor position is displayed.	−32768 — 32767	—
LIN Ignition Signal	Ignition switch LIN signal is displayed.	ON: When ignition switch is ON OFF: When ignition switch is OFF	—
Ignition SW Signal	Ignition switch direct line signal is displayed.	ON: When ignition switch is ON OFF: When ignition switch is OFF	—
Seat back setting	Seat retraction setting status is displayed.	ON: When seat retraction setting is ON OFF: When seat retraction setting is OFF	—
ACC SW	Statuses of ACC switch LIN signal and direct line signal are displayed.	OFF: When ACC switch is OFF Mismatch: When ACC switch signal does not match ON: When ACC switch is ON	—
LIN ACC Signal	ACC SW LIN signal is displayed.	ON: When ACC switch is ON OFF: When ACC switch is OFF	—
ACC SW Signal	Ignition switch direct line signal is displayed.	ON: When ACC switch is ON OFF: When ACC switch is OFF	—
Brake Lamp SW Signal	Brake light SW status is displayed.	ON: When brake light switch is ON OFF: When brake light switch is OFF	—
Smart Key Adoption	Presence/absence signal of keyless access with push button start is displayed.	Not Smart: Without keyless access with push button start Smart: With keyless access with push button start	—
MT/AT Signal	MT/AT signal is displayed.	MT: MT model AT: Other than MT model	—
Parking Break Switch Signal	Parking brake switch signal is displayed.	ON: When parking brake switch is ON OFF: When parking brake switch is OFF	—
EPB Status Signal	Electronic parking brake status signal is displayed.	ERROR: When electronic parking brake error occurs Release: When electronic parking brake is released Operate: When electronic parking brake is operated Operating: While electronic parking brake is being operated Releasing: While electronic parking brake is being released Dynamic Parking: When electronic parking brake is in dynamic parking operation	—
Shift Position Signal	Shift position signal is displayed.	D: When shift position is in D N: When shift position is in N R: When shift position is in R P: When shift position is in P L: When shift position is in L	—
Vehicle Speed Signal	Vehicle speed signal is displayed.	0 — 3986.34 km/h (MPH)	—
Remort Engine Starter Status Signal	Remote control engine starter signal is displayed.	ON: When remote control engine starter is ON OFF: When remote control engine starter is OFF	—
Driver's Door Open Status Signal	Driver’s door open/close signal is displayed.	Open: When driver’s door is open Close: When driver’s door is closed	—
Driver's Door Lock Status Signal	Driver’s door lock status is displayed.	Lock: When driver’s door is locked Unlock: When driver’s door is unlocked	—
Remote Control Key Door Lock Output Lock Signal	Remote control key door lock output status is displayed.	Output Off: Remote control key door lock output is not performed Output On: Remote control key door lock output is performed	—
Trigger SW Door Lock Output Lock Signal	Trigger switch door lock output status is displayed.	Output Off: Trigger switch door lock output is not performed Output On: Trigger switch door lock output is performed	—
Remote Control Key Door Lock Output Unlock Signal	Remote control key door unlock output status is displayed.	Output Off: Remote control key door unlock output is not performed Output On: Remote control key door unlock output is performed	—
Trigger SW Door Lock Output Unlock Signal	Trigger switch door unlock output status is displayed.	Output Off: Trigger switch door unlock output is not performed Output On: Trigger switch door unlock output is performed	—
Customize Change Request Signal : Seat Back Function	Seat retraction function change request signal is displayed.	Not Required: Seat retraction function change is not requested Required: Seat retraction function change is requested	—
Current User	The current customize setting user is displayed.	Indefinite: Unregistered user MemorySW1: Seat memory SW1 user MemorySW2: Seat memory SW2 user MemorySW3: Seat memory SW3 user KEY1: Keyless access link 1 user KEY2: Keyless access link 2 user KEY3: Keyless access link 3 user KEY4: Keyless access link 4 user KEY5: Keyless access link 5 user KEY6: Keyless access link 6 user KEY7: Keyless access link 7 user DriverMonitorSystem1: DMS1 user DriverMonitorSystem2: DMS2 user DriverMonitorSystem3: DMS3 user DriverMonitorSystem4: DMS4 user DriverMonitorSystem5: DMS5 user	—
Seat Slide Target Position	Seat slide target position is displayed.	−32768 — 32767	—
Seat Reclining Target Position	Seat reclining target position is displayed.	−32768 — 32767	—
Seat Rifter Target Position	Seat lifter target position is displayed.	−32768 — 32767	—
Seat Tilt Target Position	Seat tilt target position is displayed.	−32768 — 32767	—
Steering Wheel Information Signal	Steering wheel position signal is displayed.	LHD: LHD model RHD: RHD model	—
MT Reverse Switch Signal	MT vehicle reverse switch signal is displayed.	ON: When reverse switch is ON OFF: When reverse switch is OFF	—
Customize Change Request Signal : Mirror Function	Door mirror customize setting change request signal is displayed.	Not Required: When mirror setting change is not requested Required: When mirror setting change is requested	—
Customize Change Value : Side Mirror Tilt Down in Reverse	Door mirror reverse link change value is displayed.	OFF: Mirror customized reverse link change value is OFF ON: Mirror customized reverse link change value is ON	—
Customize Change Request Signal : Mirror Function Reset	Door mirror customization reset request signal is displayed.	Not Required: When reset is not requested Required: When reset is requested	—
Reverse Interlocking Outside Mirror Customize	Reverse-linked door mirror setting is displayed.	OFF: Linkage with reverse operation is OFF ON: Linkage with reverse operation is ON	—
Reverse Interlocking Outside Mirror Target Customize	Reverse-linked target door mirror setting is displayed.	Both Seats: When both door mirrors are set Passenger: When passenger’s door mirror is set	—
Reverse Interlocking Outside Mirror Last Momory Customize	Reverse-linked door mirror position last memory setting is displayed.	ON: When last memory setting is ON OFF: When last memory setting is OFF	—
Mirror SW Iutput Status	Door mirror switch input status is displayed.	No Operation: Unoperated state Indefinite: Unconfirmed state Up D MIR: Driver’s side mirror up direction input Down D MIR: Driver’s side mirror down direction input Right D MIR: Driver’s side mirror right direction input Left D MIR: Driver’s side mirror left direction input Up P MIR: Passenger’s side mirror up direction input Down P MIR: Passenger’s side mirror down direction input Right P MIR: Passenger’s side mirror right direction input Left P MIR: Passenger’s side mirror left direction input	—
Mirror D Vertical Output Direction	Driver’s side door mirror up/down direction output status is displayed.	No Output: No output UP: Up direction output DOWN: Down direction output	—
Mirror D Horizontal Output Direction	Driver’s side door mirror left/right direction output status is displayed.	No Output: No output RIGHT: Right direction output LEFT: Left direction output	—
Mirror P Vertical Output Direction	Passenger’s side door mirror up/down direction output status is displayed.	No Output: No output UP: Up direction output DOWN: Down direction output	—
Mirror P Horizontal Output Direction	Passenger’s side door mirror left/right direction output status is displayed.	No Output: No output RIGHT: Right direction output LEFT: Left direction output	—
Mirror D Sensor Target Vertical Position	Reloading target position corresponding to the current user is displayed (up/down).	0.0 — 5.0 V	—
Mirror D Sensor Target Horizontal Position	Reloading target position corresponding to the current user is displayed (left/right).	0.0 — 5.0 V	—
Mirror P Sensor Target Vertical Position	Reloading target position corresponding to the current user is displayed (up/down).	0.0 — 5.0 V	—
Mirror P Sensor Target Horizontal Position	Reloading target position corresponding to the current user is displayed (left/right).	0.0 — 5.0 V	—
Mirror D Sensor Target Vertical Position at R	Reloading target position corresponding to the current user is displayed (up/down).	0.0 — 5.0 V	—
Mirror D Sensor Target Horizontal Position at R	Reloading target position corresponding to the current user is displayed (left/right).	0.0 — 5.0 V	—
Mirror P Sensor Target Vertical Position at R	Reloading target position corresponding to the current user is displayed (up/down).	0.0 — 5.0 V	—
Mirror P Sensor Target Horizontal Position at R	Reloading target position corresponding to the current user is displayed (left/right).	0.0 — 5.0 V	—
Mirror D Sensor Current Vertical Position	Driver’s side door mirror position is displayed (up/down).	0.0 — 5.0 V	—
Mirror D Sensor Current Horizontal Position	Driver’s side door mirror position is displayed (left/right).	0.0 — 5.0 V	—
Mirror P Sensor Current Vertical Position	Passenger’s side door mirror position is displayed (up/down).	0.0 — 5.0 V	—
Mirror P Sensor Current Horizontal Position	Passenger’s side door mirror position is displayed (left/right).	0.0 — 5.0 V	—
Mirror D Reverse Position Memorized	Presence or absence of reverse-linked door mirror position memory is displayed (driver’s side).	Yes: When memory is present No: When memory is not present	—
Mirror P Reverse Position Memorized	Presence or absence of reverse-linked door mirror position memory is displayed (passenger’s side).	Yes: When memory is present No: When memory is not present	—
ID REGIST FLAG	ID setting signal is displayed.	DEFAULT: Default No Definition: Undefined state ID Registration: ID registered state ID Customize Editing: Customization registered state ID Delete Select: Selected ID deleted state Customize Delete Select: Selected customization deleted state ID Delete All: All IDs are deleted	—
DRIVER REGIST ID	Driver ID is displayed.	DEFAULT: Default ID1: ID1 user ID2: ID2 user ID3: ID3 user ID4: ID4 user ID5: ID5 user No Definition: Undefined ALL ID: All users Identifing: ID recognition in-progress	—
DMS Recognition Status	Personal recognition status is displayed.	OFF: Personal recognition OFF status ON: Personal recognition ON status	—
DMS 1 Memorized	Presence or absence of DMS memory is displayed.	Yes: DMS1 memory is present No: DMS1 memory is not present	—
DMS 2 Memorized	Presence or absence of DMS memory is displayed.	Yes: DMS2 memory is present No: DMS2 memory is not present	—
DMS 3 Memorized	Presence or absence of DMS memory is displayed.	Yes: DMS3 memory is present No: DMS3 memory is not present	—
DMS 4 Memorized	Presence or absence of DMS memory is displayed.	Yes: DMS4 memory is present No: DMS4 memory is not present	—
DMS 5 Memorized	Presence or absence of DMS memory is displayed.	Yes: DMS5 memory is present No: DMS5 memory is not present	—
Customize Flag	Customized setting status is displayed.	DEFAULT: Initial value Customize Present: Customization is being performed Customize Complete: Customization completed state Customize Fail: Customization failed state	—

POWER SEAT MEMORY(DIAGNOSTICS) > Freeze Frame Data　

OPERATION

For detailed operation procedures, refer to “Common (Diagnostics)”. COMMON(diag)>Freeze Frame Data
For details on freeze frame data, refer to the list. POWER SEAT MEMORY(DIAGNOSTICS)>Freeze Frame Data>LIST

POWER SEAT MEMORY(DIAGNOSTICS) > Freeze Frame Data　

LIST

Display	Contents	Note
Battery Voltage	Battery voltage is displayed.	—
Slide SW	Status of the slide switch in power seat switch is displayed.	—
Reclining SW	Status of the reclining switch in power seat switch is displayed.	—
Lifter SW	Status of the lifter switch in power seat switch is displayed.	—
Tilt SW	Status of the tilt switch in power seat switch is displayed.	—
Slide Output	Power seat control module output status is displayed. (Slide motor)	—
Reclining Output	Power seat control module output status is displayed. (Reclining motor)	—
Lifter Output	Power seat control module output status is displayed. (Lifter motor)	—
Tilt Output	Power seat control module output status is displayed. (Tilt motor)	—
ACC SW	Statuses of ACC switch LIN signal and direct line signal are displayed.	—
LIN ACC Signal	ACC SW LIN signal is displayed.	—
ACC SW Signal	Ignition switch direct line signal is displayed.	—
EPB Status Signal	Electronic parking brake status signal is displayed.	—
Vehicle Speed Signal	Vehicle speed signal is displayed.	—
Mirror SW Iutput Status	Door mirror switch input status is displayed.	—
Mirror D Vertical Output Direction	Driver’s side door mirror up/down direction output status is displayed.	—
Mirror D Horizontal Output Direction	Driver’s side door mirror left/right direction output status is displayed.	—
Mirror P Vertical Output Direction	Passenger’s side door mirror up/down direction output status is displayed.	—
Mirror P Horizontal Output Direction	Passenger’s side door mirror left/right direction output status is displayed.	—
Mirror D Sensor Current Vertical Position	Driver’s side door mirror position is displayed (up/down).	—
Mirror D Sensor Current Horizontal Position	Driver’s side door mirror position is displayed (left/right).	—
Mirror P Sensor Current Vertical Position	Passenger’s side door mirror position is displayed (up/down).	—
Mirror P Sensor Current Horizontal Position	Passenger’s side door mirror position is displayed (left/right).	—

POWER SEAT MEMORY(DIAGNOSTICS) > Active Test　

OPERATION

On [Start] screen, select [Diagnosis].

On [Select Vehicle] screen, input the target vehicle information and select [OK].

On [Main Menu] screen, select [Each System].

On [Select System] screen, select [Power Seat Memory], and then select [Next].

On [Select Function] screen, select [Active Test].

Select a location to be inspected.

For detailed operation procedures, refer to “Help” of application.
For details on active tests, refer to the list. POWER SEAT MEMORY(DIAGNOSTICS)>Active Test>LIST

POWER SEAT MEMORY(DIAGNOSTICS) > Active Test　

LIST

Active test items		Range	Contents	Execution condition
Driver’s side mirror	Mirror Driver’s side Mirror surface operation test	Up	It is possible to forcibly drive the door mirror surface motor. There are two axes: up/down and left/right directions. The test is done for driver’s side only.	• Seat motors being stopped • Mirror motors (mirror surface, electric retraction system) being stopped • Not during active test
		Down
		Left
		Right
		Cancel
Passenger’s side mirror	Mirror Passenger’s side Mirror surface operation test	Up	It is possible to forcibly drive the door mirror surface motor. There are two axes: up/down and left/right directions. The test is done for passenger’s side only.
		Down
		Left
		Right
		Cancel
Seat	Slide forward	Check	It is possible to forcibly drive the seat slide axis. The test is done for forward and rearward respectively.
	Slide forward	Cancel
	Slide rearward	Check
	Slide rearward	Cancel
	Reclining forward	Check	It is possible to forcibly drive the seat reclining axis. The test is done for forward and rearward reclining respectively.
	Reclining forward	Cancel
	Reclining rearward	Check
	Reclining rearward	Cancel
	Lifter up	Check	It is possible to forcibly drive the seat lifter axis. The test is done for up and down operations respectively.
	Lifter up	Cancel
	Lifter down	Check
	Lifter down	Cancel
	Tilt up	Check	It is possible to forcibly operate the seat tilt axis. The test is done for up and down operations respectively.
	Tilt up	Cancel
	Tilt down	Check
	Tilt down	Cancel
	Buzzer sound	Check	It is possible to forcibly sound the buzzer installed in the seat.
	Buzzer sound	Cancel

POWER SEAT MEMORY(DIAGNOSTICS) > Customize　

OPERATION

On [Start] screen, select [Diagnosis].

On [Select Vehicle] screen, input the target vehicle information and select [OK].

On [Main Menu] screen, select [Each System].

On [Select System] screen, select [Power Seat Memory], and then select [Next].

On [Select Function] screen, select [Customize].

For detailed operation procedures, refer to “Help” of application.
For details on customization, refer to the list. POWER SEAT MEMORY(DIAGNOSTICS)>Customize>LIST

POWER SEAT MEMORY(DIAGNOSTICS) > Customize　

LIST

Items	Initial setting value	Setting value	Note
Seat retraction setting∗1	OFF	OFF	DMS seat retraction setting is turned to OFF.
Seat retraction setting∗1	OFF	ON	DMS seat retraction setting is turned to ON.
Reverse-linked mirror ON/OFF setting∗1	ON	OFF	Reverse-linked mirror is set to OFF.
Reverse-linked mirror ON/OFF setting∗1	ON	ON	Reverse-linked mirror is set to ON.
Reverse-linked mirror target setting	Passenger’s seat	Both seats	Mirrors on both sides are set as a reverse-linked mirror.
Reverse-linked mirror target setting	Passenger’s seat	Passenger’s seat	Only passenger’s side mirror is set as a reverse-linked mirror.
Reverse-linked mirror position last memory setting	OFF	OFF	Reverse-linked mirror last memory is set to OFF.
Reverse-linked mirror position last memory setting	OFF	ON	Reverse-linked mirror last memory is set to ON.

∗1: For this item, customization through MFD or combination meter is possible. If a customization conflict occurs, the latest customization request is accepted.

POWER SEAT MEMORY(DIAGNOSTICS) > Work Support　

OPERATION

If the power seat CM is replaced, it is possible to read the information on setting the user performed using Subaru Select Monitor and write to the new power seat CM.

1. Read Control module setting information

On [Start] screen, select [Diagnosis].

On [Select Vehicle] screen, input the target vehicle information and select [OK].

On [Main Menu] screen, select [Each System].

On [Select System] screen, select [Power Seat Memory], and then select [Next].

On [Select Function] screen, select [Work Support].

On [Work Support] screen, select [Read Control module setting information].

According to the display screen, save and close the file.

2. Write Control module setting information

On [Start] screen, select [Diagnosis].

On [Select Vehicle] screen, input the target vehicle information and select [OK].

On [Main Menu] screen, select [Each System].

On [Select System] screen, select [Power Seat Memory], and then select [Next].

On [Select Function] screen, select [Work Support].

On [Work Support] screen, select [Write Control module setting information].

Perform the operation according to the display screen.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Trouble Code (DTC)　

OPERATION

For detailed operation procedures, refer to “Common (Diagnostics)”. COMMON(diag)>Diagnostic Trouble Code (DTC)
For details on DTCs, refer to the list. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)>LIST

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Trouble Code (DTC)　

LIST

DTC	Item	Reference
B2600	LIN Communication	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2600 LIN COMMUNICATION
B2601	LIN Circuit Low	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2601 LIN CIRCUIT LOW
B2602	Vehicle Speed Control	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2602 VEHICLE SPEED CONTROL
B2603	EPB Control	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2603 EPB CONTROL
B2604	Power Seat Memory EEPROM	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2604 POWER SEAT MEMORY EEPROM
B2605	Battery Control Low	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2605 BATTERY CONTROL LOW
B2606	Power Seat Position Sensor Circuit low	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2606 POWER SEAT POSITION SENSOR CIRCUIT LOW
B2607	Seat Motor Relay Failure	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2607 SEAT MOTOR RELAY FAILURE
B2608	Seat SW Failure	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2608 SEAT SW FAILURE
B2609	IG	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2609 IG
B260A	ACC	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B260A ACC
B2621	MIRROR SW ANOMALOUS STATE	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2621 MIRROR SW ANOMALOUS STATE
B2631	MIRROR D MOTOR CIRCUIT ANOMALOUS STATE	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2631 MIRROR D MOTOR CIRCUIT ANOMALOUS STATE
B2632	MIRROR D SENSOR CIRCUIT ANOMALOUS STATE	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2632 MIRROR D SENSOR CIRCUIT ANOMALOUS STATE
B2641	MIRROR P MOTOR CIRCUIT ANOMALOUS STATE	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2641 MIRROR P MOTOR CIRCUIT ANOMALOUS STATE
B2642	MIRROR P SENSOR CIRCUIT ANOMALOUS STATE	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC B2642 MIRROR P SENSOR CIRCUIT ANOMALOUS STATE

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2600 LIN COMMUNICATION

DTC detecting condition:

No signal is received from body integrated unit for a certain period of time (2100 ms) or more. Or, signal transmission from Power Seat & Remote Control Mirror CM is not possible for a certain period of time (2100 ms) or more.

Trouble symptom:

Seat operation is possible with manual operation, but not with memory function.
Registration is possible with memory switch, but not with keyless access key.

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2600 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK DTC.

Read the DTC of [Body Control] using the Subaru Select Monitor. BODY CONTROL(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC U0208 displayed? (Current malfunction)

Perform the diagnosis of DTC U0208.

3. CHECK BODY INTEGRATED UNIT.

Turn the ignition switch to OFF.

Replace with a normal Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2600 displayed? (Current malfunction)

Replace the body integrated unit. SECURITY AND LOCKS>Body Integrated Unit

There was something wrong with Power Seat & Remote Control Mirror CM.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2601 LIN CIRCUIT LOW

DTC detecting condition:

LIN communication circuit with the body integrated unit is shorted for a certain period of time (4000 ms) or more.

Trouble symptom:

Seat operation is possible with manual operation, but not with memory function.
Registration is possible with memory switch, but not with keyless access key.

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2601 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK DTC.

Read the DTC of [Body Control] using the Subaru Select Monitor. BODY CONTROL(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC U0208 displayed? (Current malfunction)

Perform the diagnosis of DTC U0208. BODY CONTROL(DIAGNOSTICS)>Diagnostic Procedure with Diagnostic Trouble Code (DTC)>DTC U0208 LOST COMMUNICATION WITH SEAT MEMORY

3. CHECK BODY INTEGRATED UNIT.

Turn the ignition switch to OFF.

Replace with a normal Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2601 displayed? (Current malfunction)

Replace the body integrated unit. SECURITY AND LOCKS>Body Integrated Unit

There was something wrong with Power Seat & Remote Control Mirror CM.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2602 VEHICLE SPEED CONTROL

DTC detecting condition:

Detection of 300 km/h or more continued for a certain period of time (2100 ms) or more.

Trouble symptom:

Seat operation is possible with manual operation, but registration/restoration is not possible with seat memory switch and DMS.

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2602 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK DTC.

Perform the inspection for LAN system. LAN SYSTEM (DIAGNOSTICS)>Basic Diagnostic Procedure>PROCEDURE

Is the check result OK?

Perform the inspection according to the diagnosis for LAN system.

3. CHECK VEHICLE SPEED SIGNAL OF VDC MODULE.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Brake Control]. BRAKE CONTROL (DIAGNOSTICS)>Data Monitor

FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed

With the vehicle stopped, is the displayed value abnormal?

Replace the VDC module, or inspect the vehicle speed sensor harness circuit. VEHICLE DYNAMICS CONTROL (VDC)>VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)

4. CHECK BODY INTEGRATED UNIT VEHICLE SPEED SIGNAL.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Body Control]. BODY CONTROL(DIAGNOSTICS)>Data Monitor

Front Wheel Speed

With the vehicle stopped, is the displayed value abnormal?

Replace the body integrated unit. SECURITY AND LOCKS>Body Integrated Unit

5. CHECK Power Seat & Remote Control Mirror CM.

Turn the ignition switch to OFF.

Replace with a normal Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2602 displayed? (Current malfunction)

Replace the body integrated unit. SECURITY AND LOCKS>Body Integrated Unit

There was something wrong with Power Seat & Remote Control Mirror CM.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2603 EPB CONTROL

DTC detecting condition:

Detection of EPB abnormal signal continued for a certain period of time (2100 ms) or more.

Trouble symptom:

There is no effect on power seat memory operation.

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2603 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK DTC.

Perform the inspection for LAN system. LAN SYSTEM (DIAGNOSTICS)>Basic Diagnostic Procedure>PROCEDURE

Is the check result OK?

Perform the inspection according to the diagnosis for LAN system.

3. CHECK BODY INTEGRATED UNIT.

Turn the ignition switch to OFF.

Replace with a normal Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2603 displayed? (Current malfunction)

Replace the body integrated unit. SECURITY AND LOCKS>Body Integrated Unit

There was something wrong with Power Seat & Remote Control Mirror CM.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2604 POWER SEAT MEMORY EEPROM

DTC detecting condition:

When malfunction occurs in writing/reading the memory of Power Seat & Remote Control Mirror CM.

Trouble symptom:

Seat operation is possible with manual operation, but the following situations may occur.

Seat cannot be restored to the registered position.
Memory cannot be reloaded.

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2604 displayed? (Current malfunction)

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2605 BATTERY CONTROL LOW

DTC detecting condition:

When low voltage (9 V or less) or high voltage (16 V or more) continues for 10 seconds.

Trouble symptom:

Seat operation is possible with manual operation, but the following situations may occur.

Seat position memory registration is unable to be performed.
Memory cannot be reloaded.

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is a DTC other than DTC B2605 displayed? (Current malfunction)

Perform the diagnosis for the displayed DTCs.

2. CHECK DTC.

Make sure that DTC B2605 is not displayed as past malfunction.

Is B2605 displayed? (Past malfunction)

Perform the memory recall after re-registering the memory.

3. CHECK POWER SEAT CONTROL MODULE.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Battery Voltage

Is the voltage 8 — 16 V?

4. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 2 (+) — Chassis ground (−):

(R502) No. 8 (+) — Chassis ground (−):

(R504) No. 1 (+) — Chassis ground (−):

(R504) No. 22 (+) — Chassis ground (−):

Is the voltage 8 — 16 V?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Repair the open circuit of the harness between Power Seat & Remote Control Mirror CM connector and the fuse.

5. CHECK BATTERY VOLTAGE.

Measure the battery voltage while the power seat is in operation.

Is the voltage 8 — 16 V?

Ask the user if the power window or passenger’s power seat was operated or cranking was performed while the driver’s power seat was in operation.
Even when the battery voltage is normal under ordinary circumstance, the voltage may drop to 7.5 V or less in some cases, for example at cranking.

Check the battery. STARTING/CHARGING SYSTEMS(H4DO)>Battery>INSPECTION

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2606 POWER SEAT POSITION SENSOR CIRCUIT LOW

DTC detecting condition:

When the short circuit in the pulse sensor circuit is detected during the motor operation.

Trouble symptom:

Seat memory does not operate.
Seat operation stops immediately in manual operation.

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Turn the ignition switch to OFF.

Disconnect Power Seat & Remote Control Mirror CM connector and reconnect it.

Turn the ignition switch to ON.

Move the power seat.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2606 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the connectors of all motors (slide/tilt/lifter/reclining).

Measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair or replace the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and motor connector.

3. CHECK SLIDE MOTOR.

Connect the slide motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat

4. CHECK TILT MOTOR.

Disconnect the slide motor connector.

Connect the tilt motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat

5. CHECK LIFTER MOTOR.

Disconnect the tilt motor connector.

Connect the lifter motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat

6. CHECK RECLINING MOTOR.

Disconnect the lifter motor connector.

Connect the reclining motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace Power Seat & Remote Control Mirror CM. SEATS>Front Seat

Replace the backrest frame assembly. SEATS>Front Seat

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2607 SEAT MOTOR RELAY FAILURE

DTC detecting condition:

When the same error status is detected for 500 ms continuously in motor relay output for each axis in the normal operating status.

Trouble symptom:

Seat memory does not operate.
Seat operation stops immediately in manual operation.

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Turn the ignition switch to OFF.

Disconnect Power Seat & Remote Control Mirror CM connector and reconnect it.

Turn the ignition switch to ON.

Move each axis using the power seat manual switch, and then perform the memory recall.

Move to a position different from the one registered in the memory before performing the memory recall.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2607 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK POWER SEAT CONTROL MODULE.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Slide Output
Reclining Output
Lifter Output
Tilt Output

Is [Abnormal] displayed in any of the motor output statuses?

Replace the corresponding motor.
For slide motor, tilt motor or lifter motor, replace the seat cushion frame assembly.

For reclining motor, replace the backrest frame assembly. SEATS>Front Seat

3. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the slide motor connector.

Disconnect the tilt motor connector.

Disconnect the lifter motor connector.

Disconnect the reclining motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair or replace the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and motor connector.

4. CHECK SLIDE MOTOR.

Connect the slide motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat>DISASSEMBLY

5. CHECK TILT MOTOR.

Disconnect the slide motor connector.

Connect the tilt motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat>DISASSEMBLY

6. CHECK LIFTER MOTOR.

Disconnect the tilt motor connector.

Connect the lifter motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the seat cushion frame assembly. SEATS>Front Seat>DISASSEMBLY

7. CHECK RECLINING MOTOR.

Disconnect the lifter motor connector.

Connect the reclining motor connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace Power Seat & Remote Control Mirror CM. SEATS>Front Seat

Check the battery. STARTING/CHARGING SYSTEMS(H4DO)>Battery>INSPECTION

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2608 SEAT SW FAILURE

DTC detecting condition:

When the seat switch input is detected as ON on both directions.

Trouble symptom:

Seat operation stops immediately in manual operation.

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC 2608 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK POWER SEAT CONTROL MODULE.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Slide SW
Reclining SW
Lifter SW
Tilt SW

Is [Abnormal] displayed in any of the switch statuses?

Replace the power seat switch. SEATS>Power Seat System

3. CHECK DTC.

Using the Subaru Select Monitor, perform the clear memory of [Power Seat Memory]. COMMON(diag)>Clear memory

Turn the ignition switch to OFF.

Disconnect Power Seat & Remote Control Mirror CM connector and reconnect it.

Turn the ignition switch to ON.

Move each axis using the power seat manual switch.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2608 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

4. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect motor connectors.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R504) No. 22 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair or replace the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and motor connector.

5. CHECK SLIDE SWITCH.

Disconnect the connector of power seat switch assembly.

Check the power seat switch assembly. SEATS>Power Seat System>INSPECTION > CHECK POWER SEAT SWITCH

Is the check result OK?

Replace the power seat switch. SEATS>Power Seat System

6. CHECK HARNESS (SLIDE).

Disconnect the power seat switch connector and slide motor connector.

Using a tester, measure the resistance between power seat switch connector and Power Seat & Remote Control Mirror CM connector.

Connector & terminal

(R504) No. 7 — (R200) No. 5: (slide forward)

(R504) No. 18 — (R200) No. 6: (slide rearward)

Is the resistance less than 10 Ω?

Check power seat harness.

7. CHECK TILT SWITCH.

Disconnect the connector of power seat switch assembly.

Check the power seat switch assembly. SEATS>Power Seat System>INSPECTION > CHECK POWER SEAT SWITCH

Is the check result OK?

Replace the power seat switch. SEATS>Power Seat System

8. CHECK HARNESS (TILT).

Disconnect the power seat switch connector and tilt motor connector.

Using a tester, measure the resistance between power seat switch connector and {Power Seat & Remote Control Mirror CM} connector.

Connector & terminal

(R504) No. 8 — (R200) No. 14: (tilt up)

(R504) No. 19 — (R200) No. 15: (tilt down)

Is the resistance less than 10 Ω?

Check power seat harness.

9. CHECK LIFTER SWITCH.

Disconnect the connector of power seat switch assembly.

Check the power seat switch assembly. SEATS>Power Seat System>INSPECTION > CHECK POWER SEAT SWITCH

Is the check result OK?

Replace the power seat switch. SEATS>Power Seat System

10. CHECK HARNESS (LIFTER).

Disconnect the power seat switch connector and lifter motor connector.

Using a tester, measure the resistance between power seat switch connector and Power Seat & Remote Control Mirror CM connector.

Connector & terminal

(R504) No. 10 — (R200) No. 7: (lifter up)

(R504) No. 21 — (R200) No. 4: (lifter down)

Is the resistance less than 10 Ω?

Check power seat harness.

11. CHECK RECLINING SWITCH.

Disconnect the connector of power seat switch assembly.

Check the power seat switch assembly. SEATS>Power Seat System>INSPECTION > CHECK POWER SEAT SWITCH

Is the check result OK?

Replace the power seat switch. SEATS>Power Seat System

12. CHECK HARNESS (RECLINING).

Disconnect the power seat switch connector and reclining motor connector.

Using a tester, measure the resistance between power seat switch connector and Power Seat & Remote Control Mirror CM connector.

Connector & terminal

(R504) No. 9 — (R200) No. 3: (reclining forward)

(R504) No. 20 — (R200) No. 8: (reclining rearward)

Is the resistance less than 10 Ω?

Replace Power Seat & Remote Control Mirror CM.

Check power seat harness.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2609 IG

DTC detecting condition:

When there is a difference between IG status sent via LIN communication and IG status sent from direct line for 10 seconds or more continuously.

Trouble symptom:

Mirror linked with reverse operation does not operate.
While the electric retraction system is extended manually or automatically, mirrors stop halfway and do not fully extend. (When cranking)

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2609 displayed? (Current malfunction)

2. CHECK IG SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

LIN Ignition Signal

When the ignition switch is turned to ON/OFF, are the following indications displayed?

When the ignition switch is turned to ON: ON

When the ignition switch is turned to OFF: OFF

Inspect the body integrated unit. BODY CONTROL(DIAGNOSTICS)>Basic Diagnostic Procedure

3. CHECK IG SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Ignition SW Signal

When the ignition switch is turned to ON/OFF, are the following indications displayed?

When the ignition switch is turned to ON: ON

When the ignition switch is turned to OFF: OFF

4. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Turn the ignition switch to ON.

Using the tester, measure the voltage between power seat control module connector and chassis ground.

Connector & terminal

(R502) No. 8 (+) — Chassis ground (−):

Is the voltage 9.0 — 16 V?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Repair the open circuit in harness between power seat control module connector and fuse.

5. CHECK POOR CONTACT OF CONNECTORS.

Turn the ignition switch to OFF.

Check for poor contact of Power Seat & Remote Control Mirror CM connector.

Is the check result OK?

Repair or replace the poor contact of connector.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B260A ACC

DTC detecting condition:

When there is a difference between ACC status sent via LIN communication and ACC status sent from direct line for 10 seconds or more continuously.

Trouble symptom:

Automatic electric retraction system does not extend. (When customizing ACC)
While the electric retraction system is extended manually or automatically, mirrors stop halfway and do not fully extend. (When cranking)

Wiring diagram:

Power seat system WIRING SYSTEM>Power Seat System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B260A displayed? (Current malfunction)

2. CHECK IG SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

LIN ACC Signal

When the ignition switch is turned to ON/OFF, are the following indications displayed?

When the ignition switch is turned to ON: ON

When the ignition switch is turned to OFF: OFF

Inspect the body integrated unit. BODY CONTROL(DIAGNOSTICS)>Basic Diagnostic Procedure

3. CHECK IG SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

ACC SW Signal

When the ignition switch is turned to ON/OFF, are the following indications displayed?

When the ignition switch is turned to ON: ON

When the ignition switch is turned to OFF: OFF

4. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Turn the ignition switch to ON.

Using the tester, measure the voltage between power seat control module connector and chassis ground.

Connector & terminal

(R502) No. 9 (+) — Chassis ground (−):

Is the voltage 9.0 — 16 V?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Repair the open circuit in harness between power seat control module connector and fuse.

5. CHECK POOR CONTACT OF CONNECTORS.

Turn the ignition switch to OFF.

Check for poor contact of Power Seat & Remote Control Mirror CM connector.

Is the check result OK?

Repair or replace the poor contact of connector.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2621 MIRROR SW ANOMALOUS STATE

DTC detecting condition:

When any of operation statuses (up, down, left or right) of R side mirror surface switch continues for 12 seconds.

When any of operation statuses (up, down, left or right) of L side mirror surface switch continues for 12 seconds.

Trouble symptom:

Mirror surfaces do not move even when the mirror surface switch is operated.

Wiring diagram:

Remote control mirror system WIRING SYSTEM>Remote Control Mirror System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2621 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK MIRROR SURFACE SW INPUT STATUS OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror SW Iutput Status

Does the input value change corresponding to the switch operation?

3. ACTIVE TEST OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Active Test] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Active Test

Driver’s side mirror surface up operation
Driver’s side mirror surface down operation
Driver’s side mirror surface right operation
Driver’s side mirror surface left operation
Passenger’s side mirror surface up operation
Passenger’s side mirror surface down operation
Passenger’s side mirror surface right operation
Passenger’s side mirror surface left operation

Does the mirror operate corresponding to each test operation?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

4. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the remote control mirror switch connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 5 (+) — Chassis ground (−):

(R502) No. 6 (+) — Chassis ground (−):

(R502) No. 14 (+) — Chassis ground (−):

(R502) No. 15 (+) — Chassis ground (−):

(R502) No. 16 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector.

5. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 5 — Chassis ground:

(R502) No. 6 — Chassis ground:

(R502) No. 14 — Chassis ground:

(R502) No. 15 — Chassis ground:

(R502) No. 16 — Chassis ground:

Is the resistance 1 MΩ or more?

Check remote control mirror switch unit. GLASS/WINDOWS/MIRRORS>Remote Control Mirror Switch

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector.

6. CHECK OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Vertical Output Direction
Mirror D Horizontal Output Direction
Mirror P Vertical Output Direction
Mirror P Horizontal Output Direction

Does the output status change corresponding to the switch operation?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

7. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 7 (+) — Chassis ground (−):

(R503) No. 8 (+) — Chassis ground (−):

(R503) No. 9 (+) — Chassis ground (−):

(R503) No. 17 (+) — Chassis ground (−):

(R503) No. 18 (+) — Chassis ground (−):

(R503) No. 19 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

8. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 7 — Chassis ground:

(R503) No. 8 — Chassis ground:

(R503) No. 9 — Chassis ground:

(R503) No. 17 — Chassis ground:

(R503) No. 18 — Chassis ground:

(R503) No. 19 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2631 MIRROR D MOTOR CIRCUIT ANOMALOUS STATE

DTC detecting condition:

When the mirror surface driver circuit detects overcurrent (8 A or more).
When the mirror surface driver circuit detects overheat.
When a communication (ECM internal signal) error in the mirror surface driver circuit is detected.

Trouble symptom:

Mirror surfaces do not move even when the mirror surface switch is operated.

Wiring diagram:

Remote control mirror system WIRING SYSTEM>Remote Control Mirror System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2631 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 7 (+) — Chassis ground (−):

(R503) No. 8 (+) — Chassis ground (−):

(R503) No. 9 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

3. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 7 — Chassis ground:

(R503) No. 8 — Chassis ground:

(R503) No. 9 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2632 MIRROR D SENSOR CIRCUIT ANOMALOUS STATE

DTC detecting condition:

When the horizontal sensor value is 0 V or less and the vertical sensor value is 0 V or less.
When the horizontal sensor value is 0 V or less and the vertical sensor value is 5 V or more.
When the horizontal sensor value is 5 V or more and the vertical sensor value is 0 V or less.
When the horizontal sensor value is 5 V or more and the vertical sensor value is 5 V or more.

Trouble symptom:

Mirror surfaces do not move even when the mirror surface switch is operated.

Wiring diagram:

Remote control mirror system WIRING SYSTEM>Remote Control Mirror System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2632 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 3 (+) — Chassis ground (−):

(R503) No. 4 (+) — Chassis ground (−):

(R503) No. 10 (+) — Chassis ground (−):

(R503) No. 13 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

3. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 3 — Chassis ground:

(R503) No. 4 — Chassis ground:

(R503) No. 10 — Chassis ground:

(R503) No. 13 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

4. CHECK MIRROR SURFACE POSITION SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Sensor Current Vertical Position
Mirror D Sensor Current Horizontal Position

Is the position information displayed under the following combined conditions?

[Mirror D Sensor Current Vertical Position]: Approx. 0 V and [Mirror D Sensor Current Horizontal Position]: Approx. 0 V

[Mirror D Sensor Current Vertical Position]: Approx. 5 V and [Mirror D Sensor Current Horizontal Position]: Approx. 0 V

[Mirror D Sensor Current Vertical Position]: Approx. 0 V and [Mirror D Sensor Current Horizontal Position]: Approx. 5 V

[Mirror D Sensor Current Vertical Position]: Approx. 5 V and [Mirror D Sensor Current Horizontal Position]: Approx. 5 V

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2641 MIRROR P MOTOR CIRCUIT ANOMALOUS STATE

DTC detecting condition:

When the mirror surface driver circuit detects overcurrent (8 A or more).
When the mirror surface driver circuit detects overheat.
When a communication (ECM internal signal) error in the mirror surface driver circuit is detected.

Trouble symptom:

Mirror surfaces do not move even when the mirror surface switch is operated.

Wiring diagram:

Remote control mirror system WIRING SYSTEM>Remote Control Mirror System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2631 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 17 (+) — Chassis ground (−):

(R503) No. 18 (+) — Chassis ground (−):

(R503) No. 19 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

3. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 17 — Chassis ground:

(R503) No. 18 — Chassis ground:

(R503) No. 19 — Chassis ground:

Is the resistance 1 MΩ or more?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)　

DTC B2642 MIRROR P SENSOR CIRCUIT ANOMALOUS STATE

DTC detecting condition:

When the horizontal sensor value is 0 V or less and the vertical sensor value is 0 V or less.
When the horizontal sensor value is 0 V or less and the vertical sensor value is 5 V or more.
When the horizontal sensor value is 5 V or more and the vertical sensor value is 0 V or less.
When the horizontal sensor value is 5 V or more and the vertical sensor value is 5 V or more.

Trouble symptom:

Mirror surfaces do not move even when the mirror surface switch is operated.

Wiring diagram:

Remote control mirror system WIRING SYSTEM>Remote Control Mirror System>WIRING DIAGRAM

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is DTC B2642 displayed? (Current malfunction)

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and perform the diagnosis again.

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 11 (+) — Chassis ground (−):

(R503) No. 12 (+) — Chassis ground (−):

(R503) No. 20 (+) — Chassis ground (−):

(R503) No. 21 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

3. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R503) No. 11 — Chassis ground:

(R503) No. 12 — Chassis ground:

(R503) No. 20 — Chassis ground:

(R503) No. 21 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

4. CHECK MIRROR SURFACE POSITION SIGNAL OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror P Sensor Current Vertical Position
Mirror P Sensor Current Horizontal Position

Is the position information displayed under the following combined conditions?

[Mirror P Sensor Current Vertical Position]: approx. 0 V and [Mirror P Sensor Current Horizontal Position]: approx. 0 V

[Mirror P Sensor Current Vertical Position]: Approx. 5 V and [Mirror P Sensor Current Horizontal Position]: Approx. 0 V

[Mirror P Sensor Current Vertical Position]: Approx. 0 V and [Mirror P Sensor Current Horizontal Position]: Approx. 5 V

[Mirror P Sensor Current Vertical Position]: Approx. 5 V and [Mirror P Sensor Current Horizontal Position]: Approx. 5 V

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostics with Phenomenon　

LIST

1. POWER SEAT SYSTEM

Refer to “TROUBLE SYMPTOM” for the power seat system. SEATS>Power Seat System>INSPECTION

2. MIRROR CONTROL SYSTEM

Symptoms	Note
Mirror surface does not move when operated manually (both sides/one side)	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostics with Phenomenon>INSPECTION > MIRROR SURFACE DOES NOT MOVE WHEN OPERATED MANUALLY (BOTH SIDES/ONE SIDE)
Mirror surfaces do not recover or return when being linked with reverse operation.	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostics with Phenomenon>INSPECTION > MIRROR SURFACES DO NOT RECOVER OR RETURN WHEN BEING LINKED WITH REVERSE OPERATION
Mirror surface moves automatically	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostics with Phenomenon>INSPECTION > MIRROR SURFACE MOVES AUTOMATICALLY
Mirror surface memory position is not stored	SEATS>Power Seat System>INSPECTION > THE SEAT POSITION AND DOOR MIRROR POSITION ARE UNABLE TO BE SET INTO THE MEMORY. (DRIVER’S SEAT, TYPE WITH SEAT POSITION MEMORY)
Mirror surface position is not stored when being linked with reverse operation.	SEATS>Power Seat System>INSPECTION > THE SEAT POSITION AND DOOR MIRROR POSITION ARE UNABLE TO BE SET INTO THE MEMORY. (DRIVER’S SEAT, TYPE WITH SEAT POSITION MEMORY)
Memory is not reloaded for the mirror surface only	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostics with Phenomenon>INSPECTION > MEMORY IS NOT RELOADED FOR THE MIRROR SURFACE ONLY
Cannot be customized	POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostics with Phenomenon>INSPECTION > CANNOT BE CUSTOMIZED

POWER SEAT MEMORY(DIAGNOSTICS) > Diagnostics with Phenomenon　

INSPECTION

1. MIRROR SURFACE DOES NOT MOVE WHEN OPERATED MANUALLY (BOTH SIDES/ONE SIDE)

Trouble causes:

Remote control mirror system circuit malfunction
Remote control mirror switch malfunction
Outer mirror assembly malfunction
Power Seat & Remote Control Mirror CM failure

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK BATTERY.

Perform the instructed procedures.

yes

2. CHECK FUSE.

Perform the instructed procedures.

yes

3. CHECK IGNITION SWITCH.

Perform the instructed procedures.

yes

4. CHECK DTC.

yes

Perform the instructed procedures.

5. CHECK Power Seat & Remote Control Mirror CM (REMOTE CONTROL MIRROR SW POWER SUPPLY OUTPUT).

Perform the instructed procedures.

yes

6. CHECK HARNESS (OPEN CIRCUIT).

Perform the instructed procedures.

yes

7. CHECK REMOTE CONTROL MIRROR SWITCH.

Perform the instructed procedures.

yes

8. CHECK INPUT/OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

yes

Perform the instructed procedures.

1. CHECK BATTERY.

Check the battery unit. STARTING/CHARGING SYSTEMS(H4DO)>Battery>INSPECTION

Is the battery OK?

Replace or charge the battery.

2. CHECK FUSE.

Check the fuse. GLASS/WINDOWS/MIRRORS>Relay and Fuse

Is the fuse OK?

Replace the fuse. When the replaced fuse is blown immediately, repair the power supply circuit.

3. CHECK IGNITION SWITCH.

Check the vehicle ignition switch status.

Is the ignition switch ON or ACC?

Turn the ignition switch to ON or ACC, and check the operation.

4. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Are any DTCs displayed? (Current malfunction)

Perform the diagnosis for the displayed DTCs. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

5. CHECK Power Seat & Remote Control Mirror CM (REMOTE CONTROL MIRROR SW POWER SUPPLY OUTPUT).

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground. (With the connector connected)

Connector & terminal

(R502) No. 4 (+) — Chassis ground (−):

Is the voltage 9.0 — 16 V?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

6. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the remote control mirror switch connector.

Disconnect the outer mirror assembly connector (malfunction side).

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector, and Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

Connector & terminal

(R502) No. 4 — (D149) No. 12:

(R502) No. 5 — (D149) No. 19:

(R502) No. 6 — (D149) No. 21:

(R502) No. 14 — (D149) No. 16:

(R502) No. 15 — (D149) No. 17:

(R502) No. 16 — (D149) No. 20:

(R503) No. 7 — (D5) No. 17:

(R503) No. 8 — (D5) No. 16:

(R503) No. 9 — (D5) No. 15:

(R503) No. 17 — (D15) No. 15:

(R503) No. 18 — (D15) No. 16:

(R503) No. 19 — (D15) No. 17:

Is the resistance less than 10 Ω?

Repair the open circuit of harness between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector, or Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

7. CHECK REMOTE CONTROL MIRROR SWITCH.

Check remote control mirror switch unit. GLASS/WINDOWS/MIRRORS>Remote Control Mirror Switch

Is the remote control mirror switch OK?

Replace the remote control mirror switch. GLASS/WINDOWS/MIRRORS>Remote Control Mirror Switch

8. CHECK INPUT/OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Turn the ignition switch to ON.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror SW Iutput Status
Mirror D Vertical Output Direction
Mirror D Horizontal Output Direction
Mirror P Vertical Output Direction
Mirror P Horizontal Output Direction

Perform the following operations of the mirror surface switch and check the data monitor display.

At least 20 seconds must have elapsed without operating the mirror surface switch.
Operate the mirror surface switch from one end to the other end in directions of up/down axis and left/right axis respectively for both driver’s and passenger’s sides.

Is correct input or output indication displayed for switch operation?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

2. MIRROR SURFACES DO NOT RECOVER OR RETURN WHEN BEING LINKED WITH REVERSE OPERATION

Trouble causes:

Remote control mirror system circuit malfunction
Incomplete customize setting
Outer mirror assembly malfunction
Power Seat & Remote Control Mirror CM failure

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK BATTERY.

Perform the instructed procedures.

yes

2. CHECK FUSE.

Perform the instructed procedures.

yes

3. CHECK IGNITION SWITCH.

Perform the instructed procedures.

yes

4. CHECK DTC.

yes

Perform the instructed procedures.

5. CHECK CUSTOMIZATION STATUS.

Perform the instructed procedures.

yes

6. CHECK INPUT SIGNAL.

Perform the instructed procedures.

yes

7. CHECK MIRROR SURFACE POSITION OF Power Seat & Remote Control Mirror CM.

yes

Perform the instructed procedures.

8. CHECK MIRROR SURFACE OPERATION.

yes

Perform the instructed procedures.

9. CHECK MIRROR SURFACE SENSOR VALUE OF Power Seat & Remote Control Mirror CM.

yes

Perform the instructed procedures.

10. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Perform the instructed procedures.

yes

11. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Perform the instructed procedures.

yes

12. CHECK HARNESS (GROUND SHORT CIRCUIT).

Perform the instructed procedures.

yes

13. CHECK HARNESS (OPEN CIRCUIT).

yes

Perform the instructed procedures.

1. CHECK BATTERY.

Check the battery unit. STARTING/CHARGING SYSTEMS(H4DO)>Battery>INSPECTION

Is the battery OK?

Replace or charge the battery.

2. CHECK FUSE.

Check the fuse. GLASS/WINDOWS/MIRRORS>Relay and Fuse

Is the fuse OK?

Replace the fuse. When the replaced fuse is blown immediately, repair the power supply circuit.

3. CHECK IGNITION SWITCH.

Check the vehicle ignition switch status.

Is the ignition switch ON?

Turn the ignition switch to ON, and check the operation.

4. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Are any DTCs displayed? (Current malfunction)

Perform the diagnosis for the displayed DTCs. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

5. CHECK CUSTOMIZATION STATUS.

Using the Subaru Select Monitor, check the following items in the [Customize] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Customize

Reverse-linked mirror ON/OFF setting

Is [Reverse-linked mirror ON/OFF setting] ON?

Change the customize settings.

6. CHECK INPUT SIGNAL.

Using the Subaru Select Monitor, check the input signal on the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

LIN Ignition Signal
MT/AT Signal
Shift Position Signal
Vehicle Speed Signal
Steering Wheel Information Signal
MT Reverse Switch Signal

Are relevant signals OK?

Perform diagnosis for the body integrated unit. BODY CONTROL(DIAGNOSTICS)>Basic Diagnostic Procedure

7. CHECK MIRROR SURFACE POSITION OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Sensor Current Vertical Position and Mirror D Sensor Target Vertical Position at R
Mirror D Sensor Current Horizontal Position and Mirror D Sensor Target Horizontal Position at R
Mirror P Sensor Current Vertical Position and Mirror P Sensor Target Vertical Position at R
Mirror P Sensor Current Horizontal Position and Mirror P Sensor Target Horizontal Position at R

Is the current mirror surface position identical to the reloading target position linked with reverse operation?

Function is normal. Adjust the mirror surface position of when being linked with reverse operation to the position different from the current position, register and reload the memory, and check normal operation.

8. CHECK MIRROR SURFACE OPERATION.

Operate the remote control mirror switch to move the driver’s and passenger’s side mirror surfaces up/down and left/right and check each motor rotation.

Driver’s side Up/Down direction
Driver’s side Left/Right direction
Passenger’s side Up/Down direction
Passenger’s side Left/Right direction

Does each motor rotate for three seconds or more when operating the switch?

Output circuit is normal. The current mirror surface position may be identical to the memory reloading target position. Adjust the mirror surface position to the position different from the current position, register and reload the memory, and check normal operation.

9. CHECK MIRROR SURFACE SENSOR VALUE OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Sensor Current Vertical Position
Mirror D Sensor Current Horizontal Position
Mirror P Sensor Current Vertical Position
Mirror P Sensor Current Horizontal Position

Is there any item that indicates 0 V or 5 V when the defective mirror is at up/down or left/right position?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

10. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Vertical Output Direction
Mirror D Horizontal Output Direction
Mirror P Vertical Output Direction
Mirror P Horizontal Output Direction

Is correct output indication displayed for switch operation?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

11. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector (malfunction side).

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

Outer mirror LH

(R503) No. 3 (+) — Chassis ground (−):

(R503) No. 4 (+) — Chassis ground (−):

(R503) No. 7 (+) — Chassis ground (−):

(R503) No. 8 (+) — Chassis ground (−):

(R503) No. 9 (+) — Chassis ground (−):

(R503) No. 10 (+) — Chassis ground (−):

(R503) No. 13 (+) — Chassis ground (−):

Outer mirror RH

(R503) No. 11 (+) — Chassis ground (−):

(R503) No. 12 (+) — Chassis ground (−):

(R503) No. 17 (+) — Chassis ground (−):

(R503) No. 18 (+) — Chassis ground (−):

(R503) No. 19 (+) — Chassis ground (−):

(R503) No. 20 (+) — Chassis ground (−):

(R503) No. 21 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

12. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

Outer mirror LH

(R503) No. 3 — Chassis ground:

(R503) No. 4 — Chassis ground:

(R503) No. 7 — Chassis ground:

(R503) No. 8 — Chassis ground:

(R503) No. 9 — Chassis ground:

(R503) No. 10 — Chassis ground:

(R503) No. 13 — Chassis ground:

Outer mirror RH

(R503) No. 11 — Chassis ground:

(R503) No. 12 — Chassis ground:

(R503) No. 17 — Chassis ground:

(R503) No. 18 — Chassis ground:

(R503) No. 19 — Chassis ground:

(R503) No. 20 — Chassis ground:

(R503) No. 21 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

13. CHECK HARNESS (OPEN CIRCUIT).

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

Connector & terminal

Outer mirror LH

(R503) No. 3 — (D5) No. 11:

(R503) No. 4 — (D5) No. 12:

(R503) No. 7 — (D5) No. 17:

(R503) No. 8 — (D5) No. 16:

(R503) No. 9 — (D5) No. 15:

(R503) No. 10 — (D5) No. 9:

(R503) No. 13 — (D5) No. 10:

Outer mirror RH

(R503) No. 11 — (D15) No. 11:

(R503) No. 12 — (D15) No. 12:

(R503) No. 17 — (D15) No. 15:

(R503) No. 18 — (D15) No. 16:

(R503) No. 19 — (D15) No. 17:

(R503) No. 20 — (D15) No. 9:

(R503) No. 21 — (D15) No. 10:

Is the resistance less than 10 Ω?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Repair the open circuit of harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

3. MIRROR SURFACE MOVES AUTOMATICALLY

Trouble causes:

Remote control mirror system circuit malfunction
Outer mirror assembly malfunction
Memory switch malfunction
Remote control mirror switch malfunction
Power Seat & Remote Control Mirror CM failure

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

yes

Perform the instructed procedures.

2. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Perform the instructed procedures.

yes

3. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Perform the instructed procedures.

yes

4. CHECK HARNESS (GROUND SHORT CIRCUIT).

Perform the instructed procedures.

yes

5. CHECK REMOTE CONTROL MIRROR SWITCH.

Perform the instructed procedures.

yes

6. CHECK MEMORY SWITCH.

yes

Perform the instructed procedures.

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Are any DTCs displayed? (Current malfunction)

Perform the diagnosis for the displayed DTCs. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

2. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Vertical Output Direction
Mirror D Horizontal Output Direction
Mirror P Vertical Output Direction
Mirror P Horizontal Output Direction

Is correct output indication displayed for switch operation?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

3. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the remote control mirror switch connector.

Disconnect the outer mirror assembly connector.

Disconnect the memory switch connector.

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 5 (+) — Chassis ground (−):

(R502) No. 6 (+) — Chassis ground (−):

(R502) No. 14 (+) — Chassis ground (−):

(R502) No. 15 (+) — Chassis ground (−):

(R502) No. 16 (+) — Chassis ground (−):

(R502) No. 28 (+) — Chassis ground (−):

(R502) No. 29 (+) — Chassis ground (−):

(R503) No. 3 (+) — Chassis ground (−):

(R503) No. 4 (+) — Chassis ground (−):

(R503) No. 7 (+) — Chassis ground (−):

(R503) No. 8 (+) — Chassis ground (−):

(R503) No. 9 (+) — Chassis ground (−):

(R503) No. 10 (+) — Chassis ground (−):

(R503) No. 11 (+) — Chassis ground (−):

(R503) No. 12 (+) — Chassis ground (−):

(R503) No. 13 (+) — Chassis ground (−):

(R503) No. 17 (+) — Chassis ground (−):

(R503) No. 18 (+) — Chassis ground (−):

(R503) No. 19 (+) — Chassis ground (−):

(R503) No. 20 (+) — Chassis ground (−):

(R503) No. 21 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector, or Power Seat & Remote Control Mirror CM connector and outer mirror assembly, or Power Seat & Remote Control Mirror CM connector and memory switch.

4. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the remote control mirror switch connector.

Disconnect the outer mirror assembly connector.

Disconnect the memory switch connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

(R502) No. 5 — Chassis ground:

(R502) No. 6 — Chassis ground:

(R502) No. 14 — Chassis ground:

(R502) No. 15 — Chassis ground:

(R502) No. 16 — Chassis ground:

(R502) No. 28 — Chassis ground:

(R502) No. 29 — Chassis ground:

(R503) No. 3 — Chassis ground:

(R503) No. 4 — Chassis ground:

(R503) No. 7 — Chassis ground:

(R503) No. 8 — Chassis ground:

(R503) No. 9 — Chassis ground:

(R503) No. 10 — Chassis ground:

(R503) No. 11 — Chassis ground:

(R503) No. 12 — Chassis ground:

(R503) No. 13 — Chassis ground:

(R503) No. 17 — Chassis ground:

(R503) No. 18 — Chassis ground:

(R503) No. 19 — Chassis ground:

(R503) No. 20 — Chassis ground:

(R503) No. 21 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and remote control mirror switch connector, or Power Seat & Remote Control Mirror CM connector and outer mirror assembly, or Power Seat & Remote Control Mirror CM connector and memory switch.

5. CHECK REMOTE CONTROL MIRROR SWITCH.

Check remote control mirror switch unit. GLASS/WINDOWS/MIRRORS>Remote Control Mirror Switch

Is the remote control mirror switch OK?

Replace the remote control mirror switch. GLASS/WINDOWS/MIRRORS>Remote Control Mirror Switch

6. CHECK MEMORY SWITCH.

Check memory switch unit. SEATS>Power Seat System

Is the memory switch OK?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Replace the memory switch. SEATS>Power Seat System

4. MEMORY IS NOT RELOADED FOR THE MIRROR SURFACE ONLY

Trouble causes:

Remote control mirror system circuit malfunction
Incomplete customize setting
Outer mirror assembly malfunction
Power Seat & Remote Control Mirror CM failure

If the memory cannot be reloaded for all of seats and mirrors, refer to “TROUBLE SYMPTOM” for the power seat system. SEATS>Power Seat System>INSPECTION

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK DTC.

yes

Perform the instructed procedures.

2. CHECK MIRROR SURFACE OPERATION.

yes

Perform the instructed procedures.

3. CHECK MIRROR SURFACE SENSOR VALUE OF Power Seat & Remote Control Mirror CM.

yes

Perform the instructed procedures.

4. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Perform the instructed procedures.

yes

5. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Perform the instructed procedures.

yes

6. CHECK HARNESS (GROUND SHORT CIRCUIT).

Perform the instructed procedures.

yes

7. CHECK HARNESS (OPEN CIRCUIT).

yes

Perform the instructed procedures.

1. CHECK DTC.

Turn the ignition switch to ON.

Read the DTC of [Power Seat Memory] using the Subaru Select Monitor. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

Is any of DTC B2600, B2601, B2602, B2604, B2606, B2631, B2632, B2641 or B2642 displayed? (Current malfunction)

Perform the diagnosis for the displayed DTCs. POWER SEAT MEMORY(DIAGNOSTICS)>Diagnostic Trouble Code (DTC)

2. CHECK MIRROR SURFACE OPERATION.

Operate the remote control mirror switch to move the driver’s and passenger’s side mirror surfaces up/down and left/right and check each motor rotation.

Driver’s side Up/Down direction
Driver’s side Left/Right direction
Passenger’s side Up/Down direction
Passenger’s side Left/Right direction

Does each motor rotate for three seconds or more when operating the switch?

3. CHECK MIRROR SURFACE SENSOR VALUE OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Sensor Current Vertical Position
Mirror D Sensor Current Horizontal Position
Mirror P Sensor Current Vertical Position
Mirror P Sensor Current Horizontal Position

Is there any item that indicates 0 V or 5 V when the defective mirror is at up/down or left/right position?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

4. CHECK MIRROR SURFACE OUTPUT STATUS OF Power Seat & Remote Control Mirror CM.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Mirror D Vertical Output Direction
Mirror D Horizontal Output Direction
Mirror P Vertical Output Direction
Mirror P Horizontal Output Direction

Is correct output indication displayed for switch operation?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

5. CHECK HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the outer mirror assembly connector (malfunction side).

Turn the ignition switch to ON.

Using a tester, measure the voltage between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

Outer mirror LH

(R503) No. 3 (+) — Chassis ground (−):

(R503) No. 4 (+) — Chassis ground (−):

(R503) No. 7 (+) — Chassis ground (−):

(R503) No. 8 (+) — Chassis ground (−):

(R503) No. 9 (+) — Chassis ground (−):

(R503) No. 10 (+) — Chassis ground (−):

(R503) No. 13 (+) — Chassis ground (−):

Outer mirror RH

(R503) No. 11 (+) — Chassis ground (−):

(R503) No. 12 (+) — Chassis ground (−):

(R503) No. 17 (+) — Chassis ground (−):

(R503) No. 18 (+) — Chassis ground (−):

(R503) No. 19 (+) — Chassis ground (−):

(R503) No. 20 (+) — Chassis ground (−):

(R503) No. 21 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Repair the short circuit to power supply in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

6. CHECK HARNESS (GROUND SHORT CIRCUIT).

Turn the ignition switch to OFF.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and chassis ground.

Connector & terminal

Outer mirror LH

(R503) No. 3 — Chassis ground:

(R503) No. 4 — Chassis ground:

(R503) No. 7 — Chassis ground:

(R503) No. 8 — Chassis ground:

(R503) No. 9 — Chassis ground:

(R503) No. 10 — Chassis ground:

(R503) No. 13 — Chassis ground:

Outer mirror RH

(R503) No. 11 — Chassis ground:

(R503) No. 12 — Chassis ground:

(R503) No. 17 — Chassis ground:

(R503) No. 18 — Chassis ground:

(R503) No. 19 — Chassis ground:

(R503) No. 20 — Chassis ground:

(R503) No. 21 — Chassis ground:

Is the resistance 1 MΩ or more?

Repair the short circuit to ground in harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly connector.

7. CHECK HARNESS (OPEN CIRCUIT).

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

Connector & terminal

Outer mirror LH

(R503) No. 3 — (D5) No. 11:

(R503) No. 4 — (D5) No. 12:

(R503) No. 7 — (D5) No. 17:

(R503) No. 8 — (D5) No. 16:

(R503) No. 9 — (D5) No. 15:

(R503) No. 10 — (D5) No. 9:

(R503) No. 13 — (D5) No. 10:

Outer mirror RH

(R503) No. 11 — (D15) No. 11:

(R503) No. 12 — (D15) No. 12:

(R503) No. 17 — (D15) No. 15:

(R503) No. 18 — (D15) No. 16:

(R503) No. 19 — (D15) No. 17:

(R503) No. 20 — (D15) No. 9:

(R503) No. 21 — (D15) No. 10:

Is the resistance less than 10 Ω?

Replace the outer mirror assembly. GLASS/WINDOWS/MIRRORS>Outer Mirror Assembly

Repair the open circuit of harness between Power Seat & Remote Control Mirror CM connector and outer mirror assembly.

5. CANNOT BE CUSTOMIZED

Trouble causes:

Body integrated unit malfunction
LIN communication error
Power Seat & Remote Control Mirror CM failure

Before performing diagnosis, refer to “CAUTION” in “General Description”. POWER SEAT MEMORY(DIAGNOSTICS)>General Description>CAUTION

1. CHECK BATTERY.

Perform the instructed procedures.

yes

2. CHECK FUSE.

Perform the instructed procedures.

yes

3. CHECK CUSTOMIZATION-RELATED SIGNALS.

Perform the instructed procedures.

yes

4. CHECK HARNESS (OPEN CIRCUIT).

yes

Perform the instructed procedures.

1. CHECK BATTERY.

Check the battery unit. STARTING/CHARGING SYSTEMS(H4DO)>Battery>INSPECTION

Is the battery OK?

Replace or charge the battery.

2. CHECK FUSE.

Check the fuse. GLASS/WINDOWS/MIRRORS>Relay and Fuse

Is the fuse OK?

Replace the fuse. When the replaced fuse is blown immediately, repair the power supply circuit.

3. CHECK CUSTOMIZATION-RELATED SIGNALS.

Using the Subaru Select Monitor, check the following items in the [Data monitor] of [Power Seat Memory]. POWER SEAT MEMORY(DIAGNOSTICS)>Data Monitor

Customize Change Request Signal : Mirror Function
Customize Change Value : Side Mirror Tilt Down in Reverse
Customize Change Request Signal : Mirror Function Reset
Reverse Interlocking Outside Mirror Customize
Customize Flag

Is a customization-related signal OK?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

4. CHECK HARNESS (OPEN CIRCUIT).

Turn the ignition switch to OFF.

Disconnect the Power Seat & Remote Control Mirror CM connector.

Disconnect the body integrated unit connector.

Using a tester, measure the resistance between Power Seat & Remote Control Mirror CM connector and body integrated unit.

Connector & terminal

(R502) No. 18 — (B281) No. 10:

Is the resistance less than 10 Ω?

Replace Power Seat & Remote Control Mirror CM. SEATS>Power Seat System

Repair the open circuit in harness between Power Seat & Remote Control Mirror CM connector and body integrated unit.

Power Seat Memory System Check List for Interview Date the Vehicle is Received Year Month Day
Customer’s name		Registration No.	Initial year of registration Year Month Date
Customer’s name		Vehicle model	Frame number
Interviewer	Inspector	Engine type	Odometer reading
Customer specified content • • •
Date when problem occurred	Year Month Date	Frequency of trouble occurrence	Always occurs Sometimes occurs ( times per day, times per month)
Condition of trouble occurrence (How the trouble occurs)		Weather	Fine • Cloudy • Rainy • Snowy • Others ( )
Condition of trouble occurrence (How the trouble occurs)		Temperature	°C (°F) — °C (°F)
Road conditions		Occurrence location
Accessory installation condition
Confirmation of trouble condition
Diagnostic trouble code

Door Mirror System Check List for Interview Date the Vehicle is Received Year Month Day
Customer’s name		Registration No.	Initial year of registration Year Month Date
Customer’s name		Vehicle model	Frame number
Interviewer	Inspector	Engine type	Odometer reading
Customer specified content • • •
Date when problem occurred	Year Month Date	Frequency of trouble occurrence	Always occurs Sometimes occurs ( times per day, times per month)
Condition of trouble occurrence (How the trouble occurs)		Weather	Fine • Cloudy • Rainy • Snowy • Others ( )
Condition of trouble occurrence (How the trouble occurs)		Temperature	°C (°F) — °C (°F)
Road conditions		Occurrence location
Accessory installation condition
Confirmation of trouble condition
Diagnostic trouble code

(A)	Engine compartment fuse box	(B)	Interior fuse & relay box

(1)	Fuse (30 A)	(2)	Fuse (10 A)