| Item |
Standard value |
Limit |
|
| TIMING BELT |
|||
| Auto-tensioner rod extension length (with timing belt installed) mm |
4.8 - 5.5 |
- |
|
| Auto-tensioner rod extension length (when free) mm |
12.0 |
- |
|
| Auto-tensioner rod retraction length (when pressed with force of 98 - 196 N·m) mm |
Less than 1 |
- |
|
| ROCKER ARMS AND CAMSHAFTS |
|||
| Cam height mm |
Intake valves |
35.08 |
34.58 |
| Exhaust valves |
34.26 |
33.76 |
|
| CYLINDER HEAD AND VALVES |
|||
| Cylinder head gasket surface warp mm |
0.03 |
0.2 |
|
| Cylinder head gasket surface grinding limit (including cylinder block grinding amount) mm |
- |
0.2 |
|
| Cylinder head overall height mm |
131.9 - 132.1 |
- |
|
| Valve margin mm |
Intake valves |
1.0 |
0.5 |
| Exhaust valves |
1.5 |
1.0 |
|
| Valve length mm |
Intake valves |
106.35 |
105.85 |
| Exhaust valves |
106.85 |
106.35 |
|
| Valve spring free height mm |
54.8 |
55.8 |
|
| Valve spring squareness |
2° or less |
4° |
|
| Valve stem-to-guide clearance mm |
Intake valves |
0.02 - 0.05 |
0.10 |
| Exhaust valves |
0.03 - 0.06 |
0.15 |
|
| Valve guide length mm |
Intake valves |
48 |
- |
| Exhaust valves |
55 |
- |
|
| Valve guide projection mm |
22.7 - 23.3 |
- |
|
| Valve face-to-seat contact width mm |
0.9 - 1.3 |
- |
|
| OIL PUMP AND OIL PAN |
|||
| Oil pump tip clearance mm |
0.06 - 0.18 |
- |
|
| Oil pump side clearance mm |
0.10 - 0.18 |
- |
|
| Oil pump body clearance mm |
0.040 - 0.095 |
- |
|
| PISTONS AND CONNECTING RODS |
|||
| Piston pin press-in load (at ambient temperature) N |
4,900 - 14,700 |
- |
|
| Piston ring side clearance in ring groove mm |
No. 1 |
0.03 - 0.07 |
0.1 |
| No. 2 |
0.02 - 0.06 |
0.1 |
|
| Piston ring end gap mm |
No. 1 |
0.15 - 0.30 |
0.8 |
| No. 2 |
0.30 - 0.45 |
0.8 |
|
| Oil ring |
0.20 - 0.50 |
1.0 |
|
| Connecting rod big end thrust clearance mm |
0.10 - 0.25 |
0.4 |
|
| Oil clearance at crankshaft pins mm |
0.025 - 0.040 |
0.1 |
|
| CRANKSHAFT AND CYLINDER BLOCK |
|||
| Crankshaft end play mm |
0.05 - 0.18 |
0.25 |
|
| Oil clearance at crankshaft journals mm |
0.02 - 0.04 |
0.1 |
|
| Cylinder block gasket surface warp mm |
0.05 |
0.1 |
|
| Cylinder block gasket surface grinding limit (including cylinder head grinding amount) mm |
- |
0.2 |
|
| Cylinder bore diameter mm |
75.50 - 75.53 |
- |
|
| Taper of cylinder mm |
0.01 or less |
- |
|