AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION [LF]

B3E051700000W01

1. Remove the battery duct and battery cover. (See BATTERY REMOVAL/INSTALLATION [LF].)

2. Disconnect the negative battery cable.

3. Remove the following parts.

(1) Battery, battery tray and battery box. (See BATTERY REMOVAL/INSTALLATION [LF].)
(2) Air cleaner component. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [LF].)
(3) Exhaust manifold insulator.
(4) Front tires and splash shield.
(5) Under cover.

4. Drain the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT.)

Warning
• Improperly jacking a transaxle is dangerous. It can slip off the jack and may cause serious injury.
Caution
• To prevent the torque converter and transaxle from separating, remove the transaxle without tilting it toward the torque converter.

5. Remove in the order indicated in the table.

6. Install in the reverse order of removal.

7. Add ATF to the specified level. (See AUTOMATIC TRANSAXLE FLUID (ATF) REPLACEMENT.)

8. Perform the following test. (See MECHANICAL SYSTEM TEST.)(See ROAD TEST.)

Service item

Test item

Line pressure test

Stall test

Time lag test

Road test

ATX replacement
X
 
 
 
ATX overhaul
X
X
X
X
Torque converter replacement
X
X
 
 
Oil pump replacement
X
 
 
 
Clutch system replacement
X
 
X
X

X :
Test to be performed after the service work

.

1
Input/turbine speed sensor connector
2
VSS connector
3
GND wiring harness
4
Transaxle connector
5
TR switch connector
6
GND wiring harness
7
Oil pressure switch connector (for oil filter)
8
Harness bracket
9
Transaxle mounting bolt (upper side)
10
Stabilizer control link
11
Tie-rod end ball joint
12
Lower arm ball joint
13
Drive shaft
14
Drive shaft
15
Joint shaft
16
Selector cable
17
Oil cooler
18
Starter
19
End plate cover
20
Torque converter installation nuts
21
No.1 engine mount rubber
22
Battery tray bracket
23
No.4 engine mount rubber
24
No.4 engine mount bracket
25
Transaxle mounting bolt (lower side)
26
Transaxle

Torque Converter Nuts Removal Note

1. Hold the crankshaft pulley to prevent the drive plate from rotating.

2. Remove the torque converter nuts from the starter installation hole.

No.4 Engine Mount Removal Note

1. To prevent crushing the front fender panel, insert a wood slab of appropriate size between the front fender panel and upper apron reinforcement.

Note
• Wood slab height
4 door: approx. 35 mm {1.4 in}
5 door: approx. 60 mm {2.4 in}

2. Support the engine using the SST.

3. Remove the battery tray bracket, No.4 engine mount rubber and bracket.

Transaxle Removal Note

1. Loosen the part marked A and lean the engine toward the transaxle.

2. Support the transaxle on a jack.

3. Remove the transaxle mounting bolts.

4. Remove the transaxle.

Transaxle Installation Note

1. Set the transaxle on a jack and lift it.

2. Install the transaxle mounting bolts.

Tightening torque
37.3-52.0 N·m
{3.8-5.3 kgf·m, 27.5-38.3 ft·lbf}

No.1 Engine Mount and No.4 Engine Mount Installation Note

1. Install the No.4 engine mount bracket on the transaxle case and tighten nuts.

2. Install the No.1 engine mount rubber to the crossmember and temporarily tighten bolts.

3. Place the No.4 engine mount rubber with the body stud bolts passing through the holes and tighten the new bolt as shown in the figure.

4. Place the battery tray bracket on the No.4 engine mount rubber with body stud bolts passing through the holes and tighten bolts and nuts in the order as shown in the figure.

5. Fully tighten the bolts

6. Remove the SSTs.

Torque Converter Nuts Installation Note

1. Hold the crankshaft pulley to prevent the drive plate from rotating.

Caution
• Loosely and equally tighten the torque converter nuts, then further tighten them to the specified tightening torque.

2. Tighten the torque converter mounting nuts.

Tightening torque
34.3-60.8 N·m
{3.5-6.1 kgf·m, 25.3-44.8 ft·lbf}