STEERING
STEERING COLUMN
STEERING SYSTEM
- PRECAUTION · Precautions
- PROBLEM SYMPTOMS TABLE · Troubleshooting
- ON-VEHICLE INSPECTION · Inspection
POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM
- PRECAUTION · Precautions
- PARTS LOCATION · Parts location
- SYSTEM DIAGRAM · System information
- TERMINALS OF ECU · System information
- FAIL-SAFE CHART · System information
- DATA LIST / ACTIVE TEST · System information
- SYSTEM DESCRIPTION · Troubleshooting
- HOW TO PROCEED WITH TROUBLESHOOTING · Troubleshooting
- CUSTOMIZE PARAMETERS · Troubleshooting
- PROBLEM SYMPTOMS TABLE · Troubleshooting
- DIAGNOSIS SYSTEM · Troubleshooting
- DTC CHECK / CLEAR · Troubleshooting
- FREEZE FRAME DATA · Troubleshooting
- DIAGNOSTIC TROUBLE CODE CHART · Diagnostic trouble codes
- B2602 Both of the following conditions continue:A key code confirmation signal is off The engine switch is on (IG) · Diagnostic trouble codes
- B2610 Tilt operation stops within the operation range while operating. · Diagnostic trouble codes
- B2611 Telescopic operation stops within the operation range while operating. · Diagnostic trouble codes
- B2620 The voltage of the ECU power source drops to 8 V or less and this condition continues for 10 sec. or more. · Diagnostic trouble codes
- B2621 Periodical signal from the specified ECU has stopped. · Diagnostic trouble codes
- B2624 The auto away function is disabled with the last vehicle speed signal (*1) of 10 km/h (6 mph) or more.... · Diagnostic trouble codes
- Actuator Power Source Circuit · Circuit diagnosis
- Tilt and Telescopic Manual Switch Circuit · Circuit diagnosis
- IG Power Source Circuit · Circuit diagnosis
ELECTRIC STEERING LOCK
- PRECAUTION · Precautions
- PARTS LOCATION · Parts location
- SYSTEM DIAGRAM · System information
- TERMINALS OF ECU · System information
- DATA LIST / ACTIVE TEST · System information
- SYSTEM DESCRIPTION · Troubleshooting
- HOW TO PROCEED WITH TROUBLESHOOTING · Troubleshooting
- INITIALIZATION · Troubleshooting
- PROBLEM SYMPTOMS TABLE · Troubleshooting
- DIAGNOSIS SYSTEM · Troubleshooting
- DTC CHECK / CLEAR · Troubleshooting
- DIAGNOSTIC TROUBLE CODE CHART · Diagnostic trouble codes
- B2781 Steering lock motor drive circuit is defective. Both lock and unlock position sensors detect "ON". · Diagnostic trouble codes
- B2782 Steering lock motor drive control circuit is defective. · Diagnostic trouble codes
- B2788 Different information is obtained from IG2 signals received directly from the IG2 circuit, and from IG2... · Diagnostic trouble codes
- Steering Lock Motor Drive Power Circuit · Circuit diagnosis
- Unlock Position Sensor Signal Circuit · Circuit diagnosis
- Power Source Circuit · Circuit diagnosis
STEERING COLUMN ASSEMBLY (for Manual Tilt)
- COMPONENTS · Components
- REMOVAL · Removal / installation
- DISASSEMBLY · Removal / installation
- REASSEMBLY · Removal / installation
- INSTALLATION · Removal / installation
STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic)
- COMPONENTS · Components
- INSPECTION · Inspection
- REMOVAL · Removal / installation
- DISASSEMBLY · Removal / installation
- REASSEMBLY · Removal / installation
- INSTALLATION · Removal / installation
MULTIPLEX TILT AND TELESCOPIC ECU
POWER STEERING
POWER STEERING SYSTEM
- PRECAUTION · Precautions
- PROBLEM SYMPTOMS TABLE · Troubleshooting
- ON-VEHICLE INSPECTION · Inspection
ELECTRONIC POWER STEERING SYSTEM
- PRECAUTION · Precautions
- PARTS LOCATION · Parts location
- SYSTEM DIAGRAM · System information
- TERMINALS OF ECU · System information
- FAIL-SAFE CHART · System information
- DATA LIST / ACTIVE TEST · System information
- SYSTEM DESCRIPTION · Troubleshooting
- HOW TO PROCEED WITH TROUBLESHOOTING · Troubleshooting
- CALIBRATION · Troubleshooting
- PROBLEM SYMPTOMS TABLE · Troubleshooting
- DIAGNOSIS SYSTEM · Troubleshooting
- DTC CHECK / CLEAR · Troubleshooting
- FREEZE FRAME DATA · Troubleshooting
- DIAGNOSTIC TROUBLE CODE CHART · Diagnostic trouble codes
- C1511 Torque sensor (TRQ1) signal error or stop · Diagnostic trouble codes
- C1515 This DTC is detected when torque sensor zero point calibration has not been performed. · Diagnostic trouble codes
- C1516 Steering zero point calibration is incomplete due to the steering wheel being touched during calibration. · Diagnostic trouble codes
- C1521 Motor overcurrent · Diagnostic trouble codes
- C1523 Excessively large current deviation · Diagnostic trouble codes
- C1528 Motor rotation angle sensor malfunction (e.g. An open, short to ground, or short to B+ in the rotation angle... · Diagnostic trouble codes
- C1541 This DTC is detected when vehicle speed signals via CAN communication are cut off for 3 seconds or more. · Diagnostic trouble codes
- C1551 IG power source circuit malfunction inside ECU · Diagnostic trouble codes
- C1552 This DTC is detected when power source voltage drops or remains high. · Diagnostic trouble codes
- C1581 Assist map is not written in the power steering ECU assembly. · Diagnostic trouble codes
- U0105 ECM communication error · Diagnostic trouble codes
- PS Warning Light Remains ON · Circuit diagnosis
- PS Warning Light does not Come ON · Circuit diagnosis
STEERING GEAR
- COMPONENTS · Components
- INSPECTION · Inspection
- REMOVAL · Removal / installation
- DISASSEMBLY · Removal / installation
- REASSEMBLY · Removal / installation
- INSTALLATION · Removal / installation