Honda Jazz/Fit 2005 · Service Manual

Driveshafts Disassembly (L12A/L13A except KM/KP)

Driveshafts Disassembly

Special Tools Required
Threaded adapter, 22 x 1.5 mm (  07XAC-0010100)
 

S5A1E00SXAC001T0100000D01
Sliding hammer set (  07936-5790001)
 
S3YYE00S936579T0001000D01
Boot band pincers (, commercially available)



Inboard Joint Side:


1.Remove the set ring (A) from the inboard joint.

 

S80XA00E16226600000LCAD01A

2.Remove the boot bands. Take care not to damage the boot and dynamic damper.
  • If the boot band is welded type (A), cut the boot band (B).
  • If the boot band is a double loop type (C), lift up the band bend (D), and push it into the clip (E).
  • If the boot band is a low profile type (F), pinch the boot band using the commercially available boot band pincers (G).

Welded Type 

S80XA00E16226600000LCAD02AB

Double Loop Type 

S80XA00E16226600000LCAD03DCE

Low Profile Type 

S5A1E00E16226600000LCAD03GF

3.Make a mark (A) on each roller (B) and inboard joint (C) to identify the locations of rollers and grooves in the inboard joint. Then remove the inboard joint on the shop towel (D). Be careful not to drop the rollers when separating them from the inboard joint.

 

S80XA00E16226600000LCAD04AABDC

4.Make a mark (A) on the rollers (B) and spider (C) to identify the locations of the rollers on the spider, then remove the rollers.

 

S6M2A00E16226600000LCAD01BFADEC

5.Remove the circlip (D).

6.Mark (E) the spider (C) and driveshaft (F) to identify the position of the spider on the shaft.

7.Remove the spider (C).

8.Wrap the splines on the driveshaft with vinyl tape (A) to prevent damage to the boot and dynamic damper.

 

S7A1E00E16226600000LCAD01A

9.Remove the inboard boot and dynamic damper. Take care not to damage the boot and dynamic damper.

10.Remove the vinyl tape.

Outboard Joint Side:


1.Remove the boot bands. Take care not to damage the boot and dynamic damper.

  • If the boot band is an ear clamp type (A), lift up the three tabs (B) with a screwdriver.

Ear Clamp Type 

SAA2E2CE16226600000LCAD01BA

2.Slide the outboard boot (A) to the inboard joint side. Take care not to damage the boot.

 

SAA2J00E16226600000LCJD02A

3.Wipe off the grease to expose the driveshaft and the outboard joint inner race.

4.Make a mark (A) on the driveshaft (B) at the same position of the outboard joint end (C).

 

SAA2E2CE16226600000LCAD02ABC

5.Carefully clamp the driveshaft in a vise.

 

SAA2E2CE16226600000LCAD0307XAC-001010007936-5790001A

6.Remove the outboard joint (A) using the special tool.

7.Remove the driveshaft from the vise.

8.Remove the stop ring from the driveshaft.

 

S5A1A00E16226600000LCAD08

9.Wrap the splines on the driveshaft with vinyl tape (A) to prevent damage to the boot.

 

S0X1A00E16226600000LCAD06A

10.Remove the outboard boot. Take care not to damage the boot.

11.Remove the vinyl tape.