Honda Jazz/Fit 2002 · Service Manual

DTC Troubleshooting: 11, 13, 15, 17 (Without VSA)

DTC Troubleshooting: 11, 13, 15, 17

DTC 11, 13, 15, 17:  Wheel Sensor ( Open/Short to Body Ground/Short to Power)


1.Disconnect the negative cable from the battery.

2.Disconnect the ABS control unit 25P connector.

3.Reconnect the battery cable.

4.Start the engine.

5.Measure the voltage between body ground and the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector individually (see table).

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD01Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is there battery voltage?


YES - Repair short to power in the wire between the  ABS modulator-control unit and the appropriate  wheel sensor.n


NO - Go to 6.


6.Turn the ignition switch OFF.

7.Check for continuity between body ground and the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector individually (see table).

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD02Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is there continuity?


YES - Go to 8.


NO - Go to 10.

8.Disconnect the wire harness 2P connector from the appropriate wheel sensor.

9.Check for continuity between body ground and the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector individually (see table).

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD03Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is there continuity?


YES - Repair short to body ground in the wire between the  ABS modulator-control unit and the  wheel sensor.


NO - Replace the wheel sensor.n

10.Measure the resistance between the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector individually (see table), then measure the resistance between same terminals after changing positive tester probe and negative tester probe.

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD04Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is the resistance infinity at both sides?


YES - Go to 11.


NO - Go to 13.

11.Disconnect the wire harness 2P connector from the appropriate wheel sensor.

12.Measure the resistance between the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector (see table), then measure the resistance between same terminals after changing positive tester probe and negative tester probe.

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD05Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is the resistance infinity at both sides?


YES - Repair open in the wire between the  ABS modulator-control unit and the  wheel sensor.n


NO - Replace the  wheel sensor.n

13.Check for continuity between the appropriate wheel sensor + B and GND terminals of the ABS control unit 25P connector (see table), then check for continuity between same terminals after changing positive tester probe and negative tester probe.

DTC Appropriate Terminal 
+ B GND 
11 (Right-front) FR + B:
No. 20 		FR - GND:
No. 19 
13 (Left-front) FR + B:
No. 2 		FR - GND:
No. 1 
15 (Right-rear) RR + B:
No. 22 		RR - GND:
No. 23 
17 (Left-rear) RL + B:
No. 6 		RL - GND:
No. 5 


 

SAA2E06K70100081110FAAD06Wire side of female terminalsABS CONTROL UNIT 25P CONNECTOR

Is there continuity at both sides?


YES - Repair short in the wire between the  ABS modulator-control unit and the  wheel sensor.n


NO - Check for a loose ABS control unit 25P connector. If necessary, substitute a known-good  ABS modulator-control unit, and recheck.n