Standards and Service Limits
|
2-2 |
| Item | Measurement | Qualification | Standard or New | Service Limit | |
| Ignition coil | Rated voltage | 12 V | |||
| Firing order | 1 - 3 - 4 - 2 | ||||
| Spark plug | Type | 4-door and 5-door (Japan made) models | D14Z5, D15Y6, D15Y4, D16W7 engines | NGK: ZFR5J-11
DENSO: KJ16CR-L11 |
|
| D17A1, D17A2, D17A5, D17Z1, D17Z4, D17Z5 engines | NGK: ZFR6J-11
DENSO: KJ20CR-L11 |
||||
| D15Y2, D15Y3, D16W8, D16W9 engines | NGK: BKR5E-11
DENSO: K16CR-L11 |
||||
| D17Z2, D17Z3 engines | NGK: ZFR6J-11, ZFR7J-11
DENSO: KJ20CR-L11, KJ22CR-L11 |
||||
| D14Z6, D16V1 engines | NGK:ZFR5J-11, ZFR6J-11
DENSO: KJ16CR-L11, KJ20CR-L11 |
||||
| Coupe model | D17A2, D17A8, D17A9 engines | NGK: ZFR6J-11, ZRF7J-11
DENSO: KJ22CR-L11 |
|||
| D17A5 engine | NGK: BKR6E-N-11, BKR7E-N-11
DENSO: K20PR-L11, K22PR-L11 |
||||
| 5-door (England made) model | D14Z6, D16V1 engines | NGK: ZFR5J-11, ZFR6J-11
DENSO: KJ16CR-L11, KJ20CR-L11 |
|||
| D16V3 engine | NGK: BKR5E-N-11, BKR6E-N-11
DENSO: K16PR-U11, K20PR-U11 |
||||
| Gap | 1.0-1.1 mm (0.039-0.043 in.) | - | |||
| Ignition timing | At idle (check the red mark) | M/T (in neutral): 8+2° BTDC | |||
A/T and HONDA MULTI MATIC (in  or  ): 8+2° BTDC |
|||||
| Alternator belt
NOTE: Adjust a new belt to the new belt spec., run the engine for 5 minutes, then readjust it to the used belt spec. |
Deflection with 98 N (10 kgf, 22 lbs) applied midway between pulleys | Without A/C (with A/C, see "Compressor belt" in the A/C table) | Used belt: 8.5-11.0 mm (0.33-0.43 in.) | ||
| New belt: 6.5-8.5 mm (0.26-0.33 in.) | |||||
| Tension (measured with belt tension gauge) | Without A/C (with A/C, see "Compressor belt" in the A/C table) | Used belt: 340-490 N (35-55 kgf, 77-110 lbs) | |||
| New belt: 540-740 N (55-75 kgf, 120-170 lbs) | |||||
| Alternator | Output | At 13.5 V and normal engine temperature | 70 A | ||
| Coil (rotor) resistance | at 68°F (20°C) | 1.84-2.10 ohms | |||
| Slip ring O.D. | 22.7 mm (0.89 in.) | 21.7 mm (0.85 in.) | |||
| Brush length | 19.0 mm (0.75 in.) | 5 mm (0.20 in.) | |||
| Brush spring tension | 3.3-4.1 N (1.6-1.8 kgf, 3.5-4.0 lbs) | ||||