| Item | Measurement | Qualification | Standard or New | Service Limit |
|---|---|---|---|---|
| Steering wheel | Rotational play measured at outside edge with engine running | 0-10 mm (0-0.39 in.) | ||
| Starting load measured at outside edge with engine running | 29 N (3.0 kgf, 6.6 lbs) | |||
| Gearbox | Angle of rack guide screw loosened from locked position | 15° ± 5° | ||
| Pump | Output pressure with shut-off valve closed | K20A6 engine | 7,650-8,350 kPa (78-85 kgf/cm2, 1,160-1,210 psi) | |
| K24A3 engine | 7,850-8,550 kPa (80-87 kgf/cm2, 1,140-1,240 psi) | |||
| Power steering fluid | Capacity Use genuine Honda power steering fluid | Fluid change | 0.4 [liter] (0.42 US qt, 0.36 lmp qt) | |
| System overhaul | 1.1 [liter] (1.16 US qt, 0.97 Imp qt) | |||
| Drive belt | Auto adjust | |||
| Item | Measurement | Qualification | Standard or New | Service Limit |
|---|---|---|---|---|
| Wheel alignment | Camber | Front | 0°00¢±45¢ | |
| Rear | -1°00¢±30¢ | |||
| Caster | Front | 3°12¢±1° | ||
| Total Toe | Front | 0±2 mm (0±0.08 in.) | ||
| Rear | IN 2±2 mm (0.08±0.08 in.) | |||
| Front wheel turning angle | Inside wheel | 38°50¢±2° | ||
| Outside wheel | 31°40¢ (Reference) | |||
| Wheel | Aluminum wheel runout | Axial | 0-0.7 mm (0-0.03 in.) | 2.0 mm (0.08 in.) |
| Radial | 0-0.7 mm (0-0.03 in.) | 1.5 mm (0.06 in.) | ||
| Steel wheel runout | Axial | 0-1.0 mm (0-0.04 in.) | 2.0 mm (0.08 in.) | |
| Radial | 0-1.0 mm (0-0.04 in.) | 1.5 mm (0.06 in.) | ||
| Wheel bearing | End play | Front | 0-0.05 mm (0-0.002 in.) | |
| Rear | 0-0.05 mm (0-0.002 in.) | |||
| Item | Measurement | Qualification | Standard or New | Service Limit |
|---|---|---|---|---|
| Parking brake lever | Distance travelled when lever pulled with 196 N (20 kgf, 44 lbs) of force | 6-9 clicks | ||
| Brake pedal | Pedal height (carpet removed) | LHD M/T | 144 mm (5.67 in.) | |
| LHD A/T | 148 mm (5.83 in.) | |||
| RHD M/T | 134 mm (5.28 in.) | |||
| RHD A/T | 138 mm (5.43 in.) | |||
| Free play | 1.0-5.0 mm (0.003-0.20 in.) | |||
| Master cylinder | Piston-to-pushrod clearance | No adjust | ||
| Brake disc | Thickness | Front | 25.0 mm (0.98 in.) | 23.0 mm (0.91 in.) |
| Rear | 10.0 mm (0.39 in.) | 8.0 mm (0.31 in.) | ||
| Runout | Front | ——— | 0.10 mm (0.004 in.) | |
| Rear | ——— | 0.10 mm (0.004 in.) | ||
| Parallelism | Front and rear | ——— | 0.015 mm (0.0006 in.) | |
| Brake pads | Thickness | Front | 11.0 mm (0.43 in.) | 1.6 mm (0.06 in.) |
| Rear | 9.0 mm (0.35 in.) | 1.5 mm (0.06 in.) | ||
| Item | Measurement | Qualification | Standard or New | Service Limit |
|---|---|---|---|---|
| Refrigerant | Type | HFC-134 a (R-134 a) | ||
| Capacity of system | 500-550 g (17.6-19.4 oz) | |||
| Refrigerant oil | Type | KEIHIN: SP-10 (P/N 38897-P13-003, 38898-P13-003 or 38899-P13-A01) | ||
| Capacity of components | Condenser | 25 m[liter] (5/6 fl oz, 0.9 Imp oz) | ||
| Evaporator | 45 m[liter] (1 1/2 fl oz, 1.6 Imp oz) | |||
| Each line and hose | 10 m[liter] (1/3 fl oz, 0.4 lmp oz) | |||
| Compressor | 130-150 m[liter] (4 1/3-5 fl oz, 4.6-5.3 Imp oz) | |||
| Compressor | Starter coil resistance | at 68°F (20°C) | 3.05-3.35 W | |
| Pulley-to-pressure plate clearance | 0.35-0.65 mm (0.014-0.026 in.) | |||
| Drive belt | Tension | Auto tensioner (needs no adjustment) | ||