|
Terminal number
|
Wire color
|
Terminal name
|
Description
|
Signal
|
|---|---|---|---|---|
|
4
|
GRN/RED
|
FANL (RADIATOR FAN CONTROL)
|
Drives radiator fan relay
|
With radiator fan running: about 0 V
With radiator fan stopped: battery voltage
|
|
5
|
YEL/RED
|
FANH (RADIATOR FAN CONTROL)
|
Drives A/C condenser fan relay
|
With A/C condenser fan running: about 0 V
With A/C condenser fan stopped: battery voltage
|
|
6
|
RED/BLK
|
MRLY (PGM-FI MAIN RELAY 1)
|
Drives PGM-FI main relay 1
|
With ignition switch ON (II): about 0 V
With ignition switch OFF: battery voltage
|
|
8
|
YEL/BLK
|
IGP (POWER SOURCE)
|
Power source for ECM/PCM circuit
|
With ignition switch ON (II): battery voltage
|
|
9
|
BLK
|
SG6 (SENSOR GROUND)
|
Sensor ground
|
Less than 0.5 V at all times
|
|
14
|
PUR
|
ACC (A/C COMPRESSOR CLUTCH RELAY)
|
Drives A/C compressor clutch relay
|
With compressor ON: about 0 V
With compressor OFF: battery voltage
|
|
15
|
GRY/BLK
|
IMOFPR (IMMOBILIZER FUEL PUMP RELAY)
|
Drives PGM-FI main relay 2 (FUEL PUMP)
|
About 0 V for 2 seconds after turning ignition switch ON (II), then battery voltage
With the engine running: about 0 V
|
|
16
|
BLU
|
ACPD (A/C PRESSURE SENSOR)
|
Detects A/C pressure sensor signal
|
With A/C switch ON: about 1.4−4.8 V (depending on A/C pressure)
|
|
17
|
YEL/BLK
|
APSA (ACCELERATOR PEDAL POSITION (APP) SENSOR A)
|
Detects APP sensor A signal
|
With ignition switch ON (II) and accelerator pedal pressed: about 4.7 V
With ignition switch ON (II) and accelerator pedal released: about 1.0 V
|
|
18
|
BLK
|
APSB (ACCELERATOR PEDAL POSITION (APP) SENSOR B)
|
Detects APP sensor B signal
|
With ignition switch ON (II) and accelerator pedal pressed: about 2.4 V
With ignition switch ON (II) and accelerator pedal released: about 0.5 V
|
|
19
|
YEL
|
VCC6 (SENSOR VOLTAGE)
|
Provides sensor reference voltage
|
With ignition switch ON (II): about 5.0 V
|
|
20
|
WHT
|
ETCSRLY (ELECTRONIC THROTTLE CONTROL SYSTEM (ETCS) CONTROL RELAY)
|
Drives electronic throttle control system (ETCS) control relay
|
With ignition switch ON (II): about 0 V
|
|
21
|
RED/YEL
|
SUBRLY (PGM-FI SUBRELAY)
|
Drives PGM-FI subrelay
|
With ignition switch ON (II): about 0 V
|
|
23
|
BLU/BLK
|
ELD (ELECTRICAL LOAD DETECTOR (ELD))
|
Detects ELD signal
|
With ignition switch ON (II): about 0.1−4.8 V (depending on electrical load)
|