Pony 1.2/1.3/1.5
Pony, 1.2 , 1238 cc,, 1979-85, Engine Code 4G36 ,
Ignition Data
Ignition system type: CB
Ignition coil make/type: Dia/LB-63
Supply voltage: 4.3 + Volts with ballast resistor
Primary resistance: 1.4 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Mit/T3T 03872
Contact breaker gap/air: 0.5 mm
Dwell angle: 49-55 Deg
Ignition Timing - unleaded: 3/700 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 3/700 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-3-4-2
Spark plug make: NGK
Spark plug type: BP5ES
Electrode gap: 0.75 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Mech/0.25-0.36 bar
Engine idle speed: 700 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.5 0.5 Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: n / a bar
Oil pressure: 0.8/700 bar/eng/rpm
Radiator pressure cap: 0.9 bar/type
Drive belt 1 - size: 9.5x813 KDB813 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 32/3000 Amps/eng/rpm
Regulated output: 14.3-15.8 Volts
Battery: 12/40 V/Ah
Starter motor make/type: Mit/M3T12572
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Main menu
Pony, 1.3 ,, 1298 cc, 1985-90, Engine Code G4AG,
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Dia/E-064
Supply voltage: 7 + Volts with ballast resistor
Primary resistance: 1.08-1.32 Ohms
Secondary resistance: 11600-15800 Ohms
Distributor make/type: Mit/T3T 81894
Contact breaker gap/air: 0.8 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 0 1/750 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 0 1/750 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Champion
Spark plug type: RN9YC
Electrode gap: 0.7 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Mech/0.25-0.36 bar
Engine idle speed: 750 30 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.5 Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: n / a bar
Oil pressure: n / a bar/eng/rpm
Radiator pressure cap: 0.9 bar/type
Drive belt 1 - size: PV/KIB 863 mm/type
Drive belt 2 - size: 9.5x875 KDB875 mm/type
Electrical System
Alternator output: 32/3000 Amps/eng/rpm
Regulated output: 14.3-14.9 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Mit/0.7 kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 2431221040
Tyre pressures: 1.7(24)f 1.7(24)r bar (psi)
Back to top of page or Main menu
Pony, 1.3 ,, 1299 cc, 1991- Engine Code G4-M
Ignition Data
Ignition system type: El-i
Ignition coil make/type: PS/PN22C
Supply voltage: 4.7 + Volts with ballast resistor
Primary resistance: 1.2 0.12 Ohms
Secondary resistance: 11600-15800 Ohms
Distributor make/type: Mit/-
Contact breaker gap/air: 0.8 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 5 1/700 100 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 4 1/700 100 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: NGK
Spark plug type: BPR6ES
Electrode gap: 0.7-0.8 mm
Fuel System
Fuel type: L/U +Cat
Fuel pump type/pressure: Mech/0.26-0.36 bar
Engine idle speed: 800 30 [Cat=700 50] rpm
Fast idle speed: 2800 rpm
CO level at idle speed: 1.0 0.25 [Cat=0.5 Max] Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: 14.5 bar
Oil pressure: 0.8/800 bar/eng/rpm
Radiator pressure cap: 0.83-1.10 bar/type
Drive belt 1 - size: PV/KIB863 mm/type
Drive belt 2 - size: 9.5x875 KDB875 mm/type
Electrical System
Alternator output: 65/2500 Amps/eng/rpm
Regulated output: 14.4 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Bo/0 001 311 103
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 2431221040
Tyre pressures: 1.9(28)f 1.9(28)r bar (psi)
Back to top of page or Main menu
Pony, 1.4 ,, 1439 cc, 1979-85, Engine Code 4G33
Ignition Data
Ignition system type: CB
Ignition coil make/type: Dia/LB-63
Supply voltage: 4.3 + Volts with ballast resistor
Primary resistance: 1.4 Ohms
Secondary resistance: n / a Ohms
Distributor make/type: Mit/T3T 03872
Contact breaker gap/air: 0.5 mm
Dwell angle: 49-55 Deg
Ignition Timing - unleaded: 3/700 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 3/700 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-3-4-2
Spark plug make: NGK
Spark plug type: BP5ES
Electrode gap: 0.75 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Mech/0.26-0.36 bar
Engine idle speed: 700 50 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 2.5 0.5 Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: n / a bar
Oil pressure: 0.8/700 bar/eng/rpm
Radiator pressure cap: 0.9 bar/type
Drive belt 1 - size: 9.5x813 KDB813 mm/type
Drive belt 2 - size: n / a mm/type
Electrical System
Alternator output: 32/3000 Amps/eng/rpm
Regulated output: 14.3-15.8 Volts
Battery: 12/40 V/Ah
Starter motor make/type: Mit/M3T12572
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: n / a
Cambelt Part Number: n / a
Tyre pressures: 1.9(27)f 1.9(27)r bar (psi)
Back to top of page or Main menu
Pony, 1.5 ,, 1468 cc , 1985-90 , Engine Code G4-AJ
Ignition Data
Ignition system type: El-i
Ignition coil make/type: Dia/E-064
Supply voltage: 7 + Volts with ballast resistor
Primary resistance: 1.08-1.32 Ohms
Secondary resistance: 11600-15800 Ohms
Distributor make/type: Mit/T3T 81894
Contact breaker gap/air: 0.8 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 3/750 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 3/750 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: N/S/F
Firing Order: 1-3-4-2
Spark plug make: Champion
Spark plug type: RN9YC
Electrode gap: 0.7 mm
Fuel System
Fuel type: L/U
Fuel pump type/pressure: Mech/0.26-0.36 bar
Engine idle speed: 750 30 rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.5 Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: n / a bar
Oil pressure: n / a bar/eng/rpm
Radiator pressure cap: 0.9 bar/type
Drive belt 1 - size: PV/KIB863 mm/type
Drive belt 2 - size: 9.5x875 KDB875 mm/type
Electrical System
Alternator output: 32/3000 Amps/eng/rpm
Regulated output: 14.3-14.9 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Mit/0.7 kW
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 2431221040
Tyre pressures: 1.8(26)f 1.8(26)r bar (psi)
Back to top of page or Main menu
Pony, 1.5 ,,, 1469 cc, 1991-, Engine Code G4-J
Ignition Data
Ignition system type: El-i
Ignition coil make/type: PS/PN22C
Supply voltage: 4.7 + Volts with ballast resistor
Primary resistance: 1.2 0.12 Ohms
Secondary resistance: 11600-15800 Ohms
Distributor make/type: Mit/-
Contact breaker gap/air: 0.8 mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 5 1/700 100 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: 4 1/700 100 Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-3-4-2
Spark plug make: NGK
Spark plug type: BPR6ES
Electrode gap: 0.7-0.8 mm
Fuel System
Fuel type: L/U +Cat
Fuel pump type/pressure: Mech/- bar
Engine idle speed: 800 30 [Cat=700 50] rpm
Fast idle speed: 2800 rpm
CO level at idle speed: 1.0 0.25 [Cat=0.5 Max] Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: 13.5 bar
Oil pressure: 0.8/800 bar/eng/rpm
Radiator pressure cap: 0.83-1.10 bar/type
Drive belt 1 - size: PV/KIB863 mm/type
Drive belt 2 - size: 9.5x825 KDB875 mm/type
Electrical System
Alternator output: 65/2500 Amps/eng/rpm
Regulated output: 14.4 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Bo/0 001 311 146
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 2431221040
Tyre pressures: 1.9(28)f 1.9(28)r bar (psi)
Back to top of page or Main menu
Pony, 1.5i ,, 1469 cc, 1991- ,Engine Code G4-J
Ignition Data
Ignition system type: El-ecu
Ignition coil make/type: Dia/F-088
Supply voltage: 11.0
Primary resistance: 0.8 0.08 Ohms
Secondary resistance: 10500-13900 Ohms
Distributor make/type: Mit/-
Contact breaker gap/air: n / a mm
Dwell angle: n / a Deg
Ignition Timing - unleaded: 5 2/700 100 Deg eng/rpm (without vacuum)
Ignition Timing - leaded: n / a Deg eng/rpm (without vacuum)
Timing mark location: Pulley
No 1 plug location: Pulley
Firing Order: 1-3-4-2
Spark plug make: NGK
Spark plug type: BPR6ES-11
Electrode gap: 1.0-1.1 mm
Fuel System
Fuel type: U Cat
Fuel pump type/pressure: Mech/- bar
Engine idle speed: 700 100 [1993-=825 100] rpm
Fast idle speed: n / a rpm
CO level at idle speed: 1.0 0.25 Vol %
Engine Data
Valve clearance - inlet: 0.15 h mm (hot)
Valve clearance - exhaust: 0.25 h mm (hot)
Compression pressure: 13.5 bar
Oil pressure: 0.8/800 bar/eng/rpm
Radiator pressure cap: 0.83-1.10 bar/type
Drive belt 1 - size: PV/KIB863 mm/type
Drive belt 2 - size: 9.5x825 KDB875 mm/type
Electrical System
Alternator output: 65/2500 Amps/eng/rpm
Regulated output: 14.4 Volts
Battery: 12/45 V/Ah
Starter motor make/type: Bo/0 001 108 030
Other Data
Clutch operation type: Cable
Clutch adjustment: 20-30/Pedal mm
Cambelt failure: Damage
Cambelt Part Number: 2431221040
Tyre pressures: 1.9(28)f 1.9(28)r bar (psi)
Back to top of page or Main menu